04.2018: Since this article was written, this niche in the market has been actively filled by these and other manufacturers; now there is a huge selection.

Until recently, I did not suspect the existence of such a specific type of shoe, until I encountered the conditions for its use :)

Climbing under the climbing route and going down the cliff in city sneakers turned out to be so uncomfortable that I decided that people should definitely come up with something for this! The phrase “approach shoes” was spinning in my head, literally “shoes for approaches” in the context of rock climbing or mountaineering. These are a cross between hiking shoes and climbing shoes.

They appeared because most often in the mountains, to the beginning of the route you need to walk along scree and climb simple rocks, but you still don’t want to put on tight rock shoes, and they are not always comfortable in others. Descending along rocky paths is the same story.

Different manufacturers put different meanings into the phrase “approach shoes.” Sometimes they make several models, some of which are closer to hiking shoes, others to climbing shoes, and others somewhere in the middle. Externally, “approach shoes” differ little from the masses fashionable sneakers"tourist style" All the differences are in the filling and price (the latter is not always the case).

Basically, the differences are as follows:

• Quite a stiff sole, almost like a high hiking boot for walking with a backpack

For daily use in the city this is not convenient, but in the mountains on scree it is good. The rigid sole does not press through, it is stable when the foot does not rest on the entire area, but only on part: the side, toe or heel.

• Sticky rubber

Soft, sticky rubber grips better on smooth rocks. Sometimes the same rubber is used as in climbing shoes. The opposite of this is rapid wear of the sole (abrasion, cuts).

• Pronounced edges of the sole

Not everyone, but most. Allows you to stand on small holds.

• Moderate tread

The toe of the shoe should hold up well against friction, therefore, the closer the nature of the sneaker is to a climbing shoe, the shallower the tread depth in front. In extreme cases, there is no tread on the toe of the sneaker at all. The protector on the heel is made 2-3 times less deep than in hiking boots.

• Long lacing with wide gap

Most often, the lacing ends at the middle of the big toe. A large gap between the sides of the sneaker (where the tongue is) is needed so that you can tightly tighten the lacing on the descent or feel comfortable in thick socks. On the descent, it is necessary to tighten the lacing so that the big toes do not press against the toes of the sneakers (otherwise it will be very painful).

• Hard heel edge

Needed to more confidently go down dirt slopes (it also works great on snowfields).

• No bumper at the end of the toe

The closer the nature of the sneaker is to climbing shoes, the less likely it is to encounter this element. Instead of a bumper, the entire toe of the sneaker is made quite rigid. Almost always the toe of a sneaker is made like a rock shoe (rubber-coated). This reduces wear and makes climbing in the shoes easier.

Less is better. Unfortunately, almost all of them weigh from 800 grams in size 42, and my size 44/45 is a kilogram.

Finally

Shoes don’t have to be stamped “approach shoes” and nothing else :) They weigh a fair amount and are expensive. It is quite possible that sometimes the best option would be some kind of sneakers for trail or sky running (cross-country running in the mountains). Thanks to their vanishingly light weight, they can make any climber think))). Or maybe you can find suitable shoes in a cheap store.

What do I need from shoes on the approach to the rock?

1. My approach starts from the threshold of the house, it should be full-fledged shoes in which you can come to the mountains.
2. It should be comfortable to climb in and possible to climb with a backpack on rocks up to category III-IV. Here it’s already like this: 30-40 years ago 6a climbed in boots.
3. They should be comfortable and safe to go down wet, steep paths.
4. They should be light and durable (haha).
5. They should be in a store where I can try them on.
6. They should not wear out quickly.

P.S. In my opinion, sneakers for light hiking in the mountains, when the weight of the backpack does not exceed 10 kg, ideally fit into this category by type of use.

Here is a series of La Sportiva approach shoes, here are some 5.10 models (Guide Tennie, Camp Four) / 2018: Adidas bought 5.10 in 2011 and now there are effects, I don’t know whether they are good or bad/, . Almost every manufacturer of sports shoes has either a specialized range (no one can beat La Sportiva) or models.

2012.06.16

I go to Scarpa Zen. We worked for a season and a half in the mountains on weekends, trips to the rocks and winter in the city. The flight was normal, nothing was torn. Sneakers have seen everything: dirt and rocky paths, paths with roots, loose rocks and moraines of all sizes, climbing up to IV inclusive, ascents and descents along steep grassy and scree slopes, rain, mud, wet rocks, gliders on snowfields, cutting steps (!) in the snowfield during ascent and descent, kilometers of asphalt.

Advantages:

• Fantastically durable!
• They protect the foot well.
• Very comfortable.
• Dries quickly.
• They breathe well (no membrane).
• Grippy rubber, but wears out slowly.

Flaws:

• They get wet instantly even in dew (but dry quickly).
• They could have been lighter (1000 g of exactly a pair of size 44.5).
• It doesn’t matter if they stay on the edges of sharp holds.

Will I buy it again? Don't know. The only thing that is certain is that they will be replaced by shoes from the same series - approach shoes. The difference between them and non-specialized ones is big.

After approaching the route through a 40-degree snowfield, I began to think much better about them. On the one hand, I want it to be lighter, on the other hand, I regularly find myself in conditions where the best aspects of these sneakers (which determine the weight) are revealed.

Walking on asphalt for a long time in them is uncomfortable: the sole is too hard and the heel is too hard. But that's not what they are intended for.

Winter 2015/2016

Finally, Scarpa Zen wore out - lasted 5 years. I wore them in the mountains under my backpack and a couple of times a week in the city. Exceptionally hardy. Bought new ones on sale - 5.10 Guide Tennie. 44.5 suited me, the weight of the pair was 880 g (120 g lighter than Scarp of the same size). If Scarpas fit on the foot like a shoe, then these are like felt boots: D Wide and “baggy”, but I think this will be a plus in the mountains when the foot swells on the second day after marathons on moraines and climbing.

Advantages:

• Lighter than Scarpa Zen by 120 g in the same size (880 g for a pair of size 44.5).
• Soft heel, good shock absorption.
• They fit comfortably on the leg, wide and soft.
• Cheap!
• They breathe.
• Rubber like on budget climbing shoes, more technical toe (compared to Scarpa Zen). Perhaps I can climb figure one and a half (UIAA) harder in this than in Scarpa.

Flaws:

• On dirty/dusty tiles it’s like on ice (but in other cases it’s OK, clean tiles are no longer slippery).
• Idiot thin and slippery laces, impossible to tie securely with traditional knots. It’s better to change it right away so as not to be nervous.

Everyday life constantly tires you with its bustle and monotony, so most people prefer to devote their free time active recreation in the mountains. Such walks allow you to feel positive emotions and a rush of adrenaline. To conquer steep slopes you will need not only to prepare professionally, but also to purchase one of the most important basics of mountain tourism - mountain boots. This type of shoe is particularly durable and has an impenetrable hard sole, which reliably protects the feet from all kinds of injuries in impassable rocks.

Features and Benefits

When choosing mountain boots, first of all you should pay attention not to the beautiful appearance and design, but on the quality and elasticity of the shoes.

Today, mountain boots are represented by a huge selection of models. All of them are characterized by reliability and safety during ascents. Depending on their purpose, mountaineering shoes are divided into mountain and trekking shoes. Most of these shoe models have a hard shaft and upper. In addition, the boots constantly maintain thermal balance; thanks to their special design, they can be used in conjunction with crampons.

Varieties

When going on a hiking trip, you need to worry about having comfortable shoes in advance. Since during ascents you will have to walk a lot and climb in difficult terrain, the boots must not only withstand enormous loads, but also not rub your feet, keep them dry and warm. Modern models of mountain shoes are represented by a wide range of products. They all differ in appearance, weight, and the presence of additional functions. There are the following types of mountain boots.

Climbing for mountaineering. This model is characterized by a natural leather upper and a hard sole. In addition, the boots are equipped with a special metal plate that additionally provides foot support. The external design of the shoe allows you to securely fix the foot, and the internal part is made of soft elastic materials. Mountaineering boots are not suitable for long-distance travel; they are designed for difficult mountain climbs.

For tourism . Mountain boots look similar to snowboard boots. Their main purpose is to overcome long walking distances. The outer material of the shoe is made of durable plastic that can withstand impacts. The boots have good insulation inside. The main feature of these boots is their excellent water resistance.

For hiking. The boots feature a slightly shorter upper and a thicker sole. For hiking in areas with high humidity, it is best to choose shoes with membrane fabric, but for summer tourism, boots with mesh pads are suitable. An important element of shoes is the presence of lacing. Hiking boots are comfortable, fit well on your feet, and do not wobble.

No triconi. Winter is considered one of the most wonderful periods for tourism and outdoor recreation. To cover long distances in snowfalls and frosts, you will need to purchase mountain boots without triconi. They are characterized by comfort, warmth and good stability. This model of winter sports shoes has a special sole made of ribbed material. These boots provide reliable protection against falls.

For hunting. The boots are characterized by practicality and comfort. Hunting shoes can withstand puddles, mud and rocks. Boot models should be chosen depending on the season. As a rule, such shoes have additional reinforcement of the toes and soles and are made of waterproof materials. There is also insulation inside the boots, so your feet are always protected from temperature changes. Most hunting boots are made from practical polymers such as silicone and nylon, so they are not subject to deformation or unraveling even in severe frosts.

Waterproof. This type of shoe is characterized by the presence of a tread sole that protects against slipping and falling. The boots are made of waterproof materials, so they are suitable for everyday wear.

Double. If you need to overcome high snowy peaks, then double mountain boots are the right choice. They are the lightest and warmest. The surface of the shoe does not get wet, as it is covered with a protective plastic layer. The rigidity of the sole ensures reliable fixation on rocky terrain. Most models of double boots feature a comfortable and original lacing system. These shoes can also be used for ski touring and winter hiking.

With rear entrance. For autumn and winter tourism you need to prepare not only suitable clothing, but also shoes. Boots should be of high quality, comfortable and warm. Recently, boots with rear entry have become very popular among sports shoes. Thanks to the huge range of colors available, the shoes can be worn with any outfit. There are models with fur and lace.

How to choose

Shoes are considered one of the most important elements of travel equipment. Mountain boots need to be chosen correctly, since the duration and comfort of the hike will depend on this. When buying ski boots, you should consider the following indicators.

Hardness index. This is the ability of the outer part of the boot to flex forward. Stiffness is especially important under high loads. The stiffness coefficient is calculated individually, depending on the weight. It can be from 40 to 160. It is worth paying attention to the fact that each shoe manufacturer has a different stiffness rating.

The angle of the boot. For beginner climbers and skiers, boots with a slight inclination at the top are suitable, but as for professionals, for more active skiing you will need shoes with a greater inclination.

Adjustments. The convenience of the trip depends on the presence of this element. Thanks to the adjustments, you can independently set the riding or walking mode, choose the level of rigidity and inclination of the boot.

You need to start choosing mountain boots by trying them on. The shoes must fit perfectly. It is recommended to try on boots wearing ski socks; they should not form wrinkles. The size of mountain boots is equal to the length of the foot and is indicated in centimeters. You need to put on and fasten your shoes while standing. The shoe clips do not fasten tightly at first, but then they are pressed tighter. If the shoe last does not correspond to the instep of the sole, you need to try on a different model.

When trying on boots, special attention is paid to sensations. If there is pain and discomfort, then this model is not suitable. If there is pain in the front of the leg, you need to check the tongue of the boot and the tightness of the clip. Your toes should not be pressed tightly into the front of the shoe. After trying on, you will need to do a little testing, namely, spend at least 15 minutes in the shoes. If everything is in order and there is no discomfort, then the boots are selected.

The safety of climbing largely depends on the quality and correct choice of climbing equipment. One of the important elements of a climber’s equipment is shoes. The type of boot you choose for climbing largely depends on where you intend to climb.

Types of boots for mountaineering and their choice

Mountaineering shoes are divided into tracking And mountain. The former are used for low climbs, usually in places with a warm or temperate climate. Mountain ones can be used in almost any conditions.

Trekking footwear is divided into sneakers, light and heavy boots. All of them are made of lightweight materials and cannot protect the foot from prolonged exposure to dampness and cold. The heavy variety can be used in conjunction with simple transitions.

Mountain boots are also divided into three groups:

• Alpine boots have a fairly rigid top and shaft. Most models are suitable for use with cats.
• One-and-a-half boots have two layers, this helps maintain normal thermal balance.
• Double mountain boots are made using special insulation and are designed for climbing serious snowy peaks.

Before going to the store, decide what specific mountaineering boots you need. To do this, you need to decide which route your trip will take.

Most often, trekking shoes are recommended for beginners. Models vary slightly from manufacturer to manufacturer. Most often the difference lies in the width of the pad. Therefore, before making your final choice, try on several pairs from different manufacturers.

How to wear it in correctly

When purchasing, you should choose boots that are a little larger than you usually buy. This way, when descending from the top, your weight will put less pressure on thumb legs.

• After purchasing, you should break in your shoes. You can’t go straight to the mountains in new boots. To wear it in, you just need to walk around the room in your new clothes. This needs to be done for at least an hour.
• When climbing for the first time in new shoes, you should wrap your heels with adhesive tape. This will save your feet from painful blisters.

How to dry shoes correctly

Shoe maintenance on the go and at home differs. When you come back from climbing, you need to dry your boots.

• When drying on a heat source, it is necessary to exclude the possibility of warping of the material. The easiest option is to stuff your shoes tightly with newspapers. Nowadays you can find special pads in specialized stores.
• All mountain shoes are capable of absorbing moisture. Therefore, experienced athletes recommend treating it with special water-repellent sprays. Moreover, this should be done not only before leaving, but also during the ascent.
• Ideally, you should have two pairs of shoes with you, but this is not always possible. Therefore, you will have to dry your boots right at the rest stop. The best option would be to use sunlight and wind. Experienced climbers can also dry their shoes near a fire, but there is a risk of warping. Therefore, this must be done very carefully.
• The litter is dried separately from the boots. This is a mandatory rule. It is impossible to dry them without pulling them out, especially in hiking conditions. With wet bedding, your feet will get cold pretty quickly.

Additional features

An important characteristic of shoes for climbers is the presence or absence of a welt for attaching crampons. Trekking shoes are not intended for use with this equipment. Its upper and sole are too soft.
Boots for more serious hikes have a more rigid frame. They also have one or two welts. Moreover, in high-mountain variants there are always two of them. This is due to the need to wear crampons with a rigid type of fastening.

You should also pay attention to the choice of bedding. For simple hikes, membrane insoles are suitable. They will provide good ventilation. For more difficult multi-day climbs, it is better to use two-layer bedding. One layer is membrane, the second is made of rubber. This ensures their long service life.

Comfort during use depends on the correct choice of shoes for mountain climbing. Wearing the wrong shoes can cause injury. Also, when choosing, you should consider the possibility of using additional equipment.

They run small! You need to take a size larger than yours! If you wear size 42, you need to choose size 43!

Upper material – nubuck (t. 2.4 mm) with water-repellent impregnation. Easy to care for and resistant to wear. The lining is a practical synthetic material with a Sympatex ® membrane. It removes excess moisture well and retains heat. Replaceable insole: the first layer is Cambrelle ®, the second is antistatic non-woven material. Protects the foot from overheating. Highly resistant to wear. Durable nylon lacing ensures a snug, comfortable fit. Vibram ® T.D. outsole. (rubber + thermoformed micro. Suitable for mountaineering in crampons) – highly durable and non-slip Multi-directional tread guarantees optimal traction with the surface There is a rubber lining along the entire perimeter of the sole, which provides additional protection for the upper material from mechanical damage and exposure to aggressive external environments Characteristics: Weight: 650 g (1/2 pair 42 sizes) Manufacturer: Lomer, Italy Size range: 40-46 REVIEWS: Review from Survival Panda

The upper material is nubuck (th. 2.4 mm) with water-repellent impregnation. Easy to care for and resistant to wear. The lining is a practical synthetic material with a Sympatex ® membrane. It removes excess moisture well and retains heat. Replaceable insole: the first layer is Cambrelle ®, the second is antistatic non-woven material. Protects the foot from overheating. Highly resistant to wear. Durable nylon lacing ensures a snug, comfortable fit. Vibram ® T.D. outsole. (rubber + thermoformed micro. Suitable for mountaineering in crampons) – highly durable and non-slip Multi-directional tread guarantees optimal traction with the surface There is a rubber lining along the entire perimeter of the sole, which provides additional protection for the upper material from mechanical damage and exposure to aggressive external environments Characteristics: Weight: 650 g (1/2 pair 42 sizes) Manufacturer: Lomer, Italy Size range: 40-46 REVIEWS: Review from Survival Panda

Description: This double boot is designed for high altitude climbing in the most extreme weather conditions. The weight of a pair of size 42 is 2520 g. The gaiter is made of durable elastic and water-repellent Cordura fabric. Additionally, the lower part is reinforced with heavy-duty Kevlar. The gaiter is securely fixed on the leg due to the elastic band located on top. These boots have a multi-layer construction. There are 14 layers in total, 8 of them are high-tech thermal insulation materials that prevent heat loss. The outer and inner boots have an innovative lacing system that allows you to lace the boots with one hand without removing your gloves, which is sometimes important at very low temperatures. Special FitSystem loops help you put on your boots without much difficulty. The waterproof Velcro closure provides excellent protection against snow penetration. The model is equipped with two welts for attaching hard crampons, but can also be used with semi-hard or soft crampons. The boots have a wear-resistant Vibram sole, the quality of which has been tested by time. There is a special insert on the toe for better grip on rocky terrain. The set includes two insoles, which allows you to adjust the boots to your feet as well as possible. Gaiters: Stretch Cordura + PU Coated Fabric + Water Repellent Cordura – Neoprene Thermal Barrier Outer Boot: High tenacity nylon upper with dual strength polyethylene padding and bonded to heat reflective aluminum lining Removable Boot: Water repellent Lorica + Thermal Barrier + Aluminum + Mesh lining Removable insole: thermal insulating Insole: 5mm thermal insulating carbon fiber with polyester center insert + polyethylene and aluminum insulation Patent: registered design and liner lacing system Sizes: 39-47 in 0.5 Features: Upper High tenacity nylon upper with dual dencity PE padding and lined with thermo reflective aluminum Lining no Inner sole 5 mm insulating structured carbon fiber, polyestercentral insert - PE and aluminum insulation Sole Highly insulating Vibram with climbin rubber insert Welt for crampons yes Area of ​​application High-altitude mountaineering Size 39-47 through 0.5 Pair weight 2520 g Technologies: Vibram rubber

Lightweight 3-4 season boots for mountaineering and technically difficult hikes. The upper of the boot is made of high-quality waterproof leather and Teramida fabric. Cushions in the ankle area for ankle support. The Boreal Dry-Line system allows the foot to breathe and keeps water out of the boot. Rubber welt on the toe and sides for additional protection. Features 2.6mm waterproof leather and abrasion-resistant Teramida, HFS ankle support, Boreal Dry-Line for absolute waterproofness and breathability, Vibram Mulaz rubber sole, dual stiffness, with vibration-damping inserts, compatible with semi-rigid and soft crampons Features One-piece upper Upper material: leather 2 ,6mm, Teramida fibers Membrane: Boreal Dry-Line ® System Sole: Vibram Mulaz Vibration damping system Midsole: Boreal PBG 650 Operating mode: short mountaineering routes, difficult trekking Welt for attaching crampons Moisture removal system: Boreal Dry Line Weight per pair size 7 UK, city: 1560

Climbing boots made of leather with a welt for single-welted crampons will be your reliable companion on the climb! The outer part of the boot is made of water-resistant leather with a thickness of 2.6 mm. with Teramida fabric inserts. Boreal Dry-Line lining - maximum steam removal and moisture protection. Boreal PGB-650 midsole with lateral reinforcements for torsional rigidity and vibration-absorbing layer. New Vibram Mulaz outsole with vibration-damping TPU and EVA heel inserts. TPU welt for single welt cats. Purpose: mountaineering Season: all-season Upper material: leather Membrane: yes Rubber welt to protect feet and shoes. HFS heel support system.

Description The Nepal Evo model is ideal for technical and ice routes. The boots are made of 3 mm full-cut leather with a special water-repellent treatment. This way, there is a minimum number of seams, so the boot does not get wet. Thanks to the Gore-Tex membrane, the boots are waterproof but still breathable. The rubber welt along the entire perimeter of the boots perfectly protects the leather from wear and tear during high-speed descents on scree. The model has a small elastic gaiter, which additionally prevents snow and ice chips from getting inside the boots. Nepal Evo has two welts for attaching hard crampons, but can also be used with semi-hard or soft crampons. Vibram outsole with Impact Brake System technology. Thanks to the angled arrangement of the tread elements, it can significantly reduce the impact load on the joints when walking. Provides excellent traction during descent or ascent, even in wet conditions. The model uses 3D Flex technology, which allows you to combine reliable ankle support with the flexibility of the boot necessary for ease of movement. This is achieved through the use of a special material in the instep area, due to which the boot takes on an anatomical shape. The set includes special removable Velcro tabs that will allow you to adjust the boots as much as possible. By using special clamps for laces, you can independently adjust the tension in the foot and ankle areas. A pair of size 42 weighs 2050 grams Upper: 3mm water-repellent Idro-Perwanger ® leather Lining: Gore-Tex ® Insulated Comfort Insole: 9mm insulated Ibi-Thermo Sole: Vibram ® with emergency braking Sizes: 37-48 through 0 ,5 Patent: Registered Design Benefits and Features Allows the ankle to move freely while still providing adequate support Removable tongue attached to the top of the boot Nylon loop for quick release of the lock from the lacing system Outer fabric that "breathes" and is moisture resistant outsole Vibram rubber, designed to reduce the impact load when walking and running, is made of genuine leather Awards Nepal Evo GTX Climbing Magazine Editor's Choice La Sportiva Nepal Evo GTX is the Climbing Magazine Editor's Choice winner. The Nepal Evo GTX is the most versatile mountaineering boot. Real must have! The Nepal Evo GTX is excellent for classic and technical climbing and is easily adjustable thanks to its removable tongues. 3.2mm full-length water-repellent leather provides excellent durability. Great for cold days and where you need good support and protection on the trails. Care instructions Clean your boots after each use. All external and internal hinges should be thoroughly cleaned and dried to reduce the risk of rust on metal products. Care for the leather outside and inside the shoe using special products. Leave the boots to dry outdoors, protecting from direct sunlight and away from heating devices. La Sportiva recommends choosing your boot size carefully: your foot should fit well in the last. By keeping your foot snug in the boot, you minimize the risk of tearing the Gore-Tex inner membrane. Although La Sportiva boots are made from waterproof, specially treated leather that is resistant to dirt, improper use can cause the leather to dry out and become damaged. After each use, boots must be cleaned of dirt and dust by rinsing under a gentle stream of water. If necessary, the insole can be removed and the boots themselves can be placed in a cool, dry place for ventilation. It is best to remove the insole after each use and shake out any gravel that may have accidentally gotten inside the shoe and could damage the integrity of the Gore-Tex membrane. Do not place newspaper or other paper inside the boots as this may slow down the drying of the boots. Never dry your boots in the open sun or near heating devices. LEATHER CARE: Never treat these leathers with oil-containing products as this may adversely affect the waterproof performance and overall life of the boot. We recommend Nikwax water-repellent products for the care of your shoes. These products are suitable for caring for models with a Gore-Tex membrane. Products must be applied to damp skin to improve absorption into the boot fabric. The effect of this product lasts quite a long time, but not permanently. The product can be reapplied as needed or after each use in harsh conditions. Please be careful as these products darken the boot leather. GORE-TE CARE For leather models with a Gore-Tex membrane, we recommend using a water- and wax-based product such as Nikwax to simultaneously protect leather and nylon from water. These products do not affect the technical characteristics and “breathing” properties of materials, including Gore-Tex, but create the necessary waterproof film on the boot.

The outer layer is made of high-strength wear-resistant materials Teramida and Lorica. Bi-Flex system for unrivaled flexibility and ride comfort. HFS ankle support for better fit. The inner layer is Boreal Dry-Line lining. Moisture-wicking fibers and breathability waterproof membrane maintain a comfortable microclimate inside the boot. Midsole with inserts for increased torsional rigidity and EVA foam for vibration damping and thermal insulation. Single welt Vibram Mulaz sole for use with semi-automatic crampons. wear-resistant synthetic outer layer made of Teramida and Lorica Bi-Flex - flexible shaft provides greater walking comfort HFS - Boreal Dry-Line ankle support system - moisture wicking and waterproof Membrane: Boreal Dry-Line ® System Midsole: Boreal PBG 650 Operating mode: summer climbing, winter walks in the mountains, travel on glaciers Weight of a pair of size 7 UK, g: 1491

Double boots for high-altitude ascents up to GOST 7000-80 m Article: 296GI Upper: suede Lining: Dentex Last: PD75 elongated on the last Fullness: medium Midsole: LaSpoFlex 0.8 mm (front section only) Sizes: 34-45 through 0.5 Pair weight: 2300 G Color Grey/Yellow Description Double boots for high-altitude ascents up to GOST 7000-80 m. Ideal for climbing northern walls, for winter mountaineering and long stays at high altitude. Simple, comfortable and precise fit. A distinctive feature of this model is the original lacing system for both the outer and inner boots, which allows you to lace the boot with one hand, in extreme conditions - with gloves. Very light, a pair of size 42 weighs only 2300 g. Can be used with any type of cat. Outer boot: PU-Tech synthetic fabric combined with a double layer of polyethylene with two densities. Inner: perforated thermoformed polyethylene Lining: Aluminum insulation combined with a protective wear-resistant perforated layer Inner sole: 5 mm thick. made of carbon fiber, with thermal structure, with a central polyester insert + aluminum thermal insulation Sole: Vibram ® + high protective rubber welt If you love mountaineering, then the La Sportiva Spantik double mountaineering boots will be an indispensable purchase for you. Thanks to the high-quality materials from which they are made, your feet will be warm even at an altitude of 7000-80 meters according to GOST. Aluminum thermal insulation over the entire area of ​​the boot in combination with high-quality polyester and polyethylene will not allow wind, moisture or frost to pass through. The Vibram outsole is also resistant to harsh outdoor conditions and will provide good traction on icy surfaces. For climbers, the ability to lace with one hand will be a definite plus, for example, if you are hanging at a height and need to adjust your boot. Plus, you can attach absolutely all types of climbing crampons to the sole: both rigid and semi-rigid - fortunately, this model supports this possibility (on most models it is possible to attach only a certain type of crampons). A good fit of the boots, as well as a light weight of just over two kilograms, will not cause any discomfort when moving.

Leader in European sales. Mountain climbing boots with crotches. Designed for intensive use from early spring to late autumn. The Boreal Dry Line system ensures optimal temperature and humidity inside the boot. The vibration-absorbing EVA layer reduces shock loads on the joints and spine. The special tread pattern provides reliable grip on the surface. Features: one-piece leather upper without seams; outer water-repellent impregnation; rigid sole allows you to fasten crampons of any design; double-sided welt for crampons; deep tread pattern; four-layer midsole; vibration-absorbing layer made of elastic EVA material; two-layer ventilated insole with antibacterial impregnation and instep pad; moisture-wicking surface of the insole does not cause allergies the upper edge of the boot is very processed from the inside soft skin quick lacing system special water-repellent laces the kit includes a can of moisture-wicking impregnation and a Boreal mini-catalog Characteristics One-piece upper: Yes Upper material: Split Leather 2.6 mm Membrane: Sympatex Sole: Boreal Mount FDS-3 Vibration damping system: Yes Midsole: triple Operating mode: Designed for intensive use from early spring to late autumn. Welt for attaching crampons: Yes Insole ventilation: Yes Moisture removal system: Boreal Dry Line Weight of a pair of size 41 rus, g: 1756 m

Women's freeride ski boots Grilamid upper Thermoformable inner boot EZ Wrap Liners Tech, AT, Skitrab TR2 bindings Vibram outsole Pair weight 1640 g Size 23-27.5 through 0.5 Outer boot and shaft: 1. Compact outer boot made of Grilamid® of reduced volume and weight with high performance. The cuff provides freedom of movement, and the innovative rear diffuser provides greater stability and ankle security when the boot is in riding mode. 2. The SpectreTM's Dual-Axis CuffTM consists of two separate elements that work together: 1) a dual-layer Climbing System ControlTM cuff with dual Pebax® closures provides lateral control and ankle mobility for technical climbing; 2) carbon reinforced Grilamid® Vertebra TechnologyTM enhances power transfer forward and reverse. 3. Walking mode provides 60° range of motion, compatible with AT, Tech and Skitrab TR2 mounts. The 17mm rise ensures a comfortable fit even during prolonged use. 4. Shell Line: Reinforced area helps minimize the amount of deformation of the outer boot. 5. Dual Reinforced Tongue: Patented Grilamid® tongue has two parts that overlap during riding and provide structural rigidity during descents and walking. They make walking easier, increasing mobility and flexibility (stiffness index 125). 6. 4BT TechTM Last: Neutral shape with 102.5mm internal width keeps your foot in a comfortable position to tackle technical terrain. It is similar to the shape used in the Spitfire, Sideral and Starlet boots, but is wider for greater comfort in the toe. 7. The removable WarmSoleTM insole made of thermally insulating polyurethane eliminates direct contact of the foot with the outer boot, increases the thermal insulation qualities of the boot and makes it one of the warmest ski boots with 4 clasps. Fastener: 8. Patented Pegasus Buckle PlusTM clips - easy to use even with gloves. 9. Power Strap: Wider-reach Velcro closure secures the boot for efficient power transfer when skiing downhill. 10. Vertebra TechnologyTM Exoskeleton Technology: Carbon-reinforced, flexible, ergonomic Grilamid® structure. It is part of the boot and provides maximum safety and precision in skiing mode, freely conducting energy from the leg to the boot and the ski itself on difficult ski slopes on steep slopes. eleven. Patented Walk/Ride Mechanism: Quick closure system to transition from riding to walking in one motion. 12. The adjustment system allows you to change the angle of the boot in 3 positions: 10°, 14°, 18°. Outsole and Binding Compatibility: 13. Vibram® outsole: Dual-density with abrasion-resistant toe and heel pods for easier climbing on technical approaches. A special centering system that helps to quickly attach the boot to the ski bindings. 14. Compatible with Tech, AT and Skitrab TR2 mounts. 15. EZ Inner Boot: Pre-shaped inner boot fits to the last of the outer boot for a comfortable fit. The liner can be thermoformed to suit the individual characteristics of the foot. Overlapping boot closure for greater comfort and support while descending the mountain. La Sportiva Shadow is a women's freeride ski boot. It combines the power, tenacity and precision of a downhill ski boot with the lightness and agility of a next-generation ski mountaineering boot. The boot's design is designed to allow you to enjoy powder skiing with enhanced ski control and secure TR2 bindings. Care and Maintenance 1. Clean your boots with mild soap and water. 2. Remove liners after each use and dry liners and outers in a warm, dry place away from heat sources such as fireplaces, stoves, heaters, radiators or ovens. 3. Out of season or when storing boots for a long time, make sure that the outer and inner boots are properly dried. They should be stored away from sunlight, in a well-ventilated area at room temperature and with the buckles fastened. 4. The plastic used in boots may develop a white film over time. This is fine. The film can be removed with soap, water and a soft cloth. 5. Do not store ski boots at temperatures above 45°C (110°F). Warranty La Sportiva warrants to the end retail shoe purchaser that the product meets the specifications stated in the user manual for a period of 1 year from the date of purchase. If you find a defect in the product you purchased, you can return the product to the store where you purchased it, or, if it is impossible to return the product to the store, contact La Sportiva directly. The letter must indicate the cause of the defect, the operating conditions of the shoes, and attach photographs ( full appearance of the shoes, type of sole, location of the defect), indicate the ID number of the pair (a combination of numbers and letters on a white sewn-in tongue), the size of the pair and the store where the shoes were purchased. After this, your request will be sent to the manufacturer, who will decide on repair or replacement with a similar product. If for some reason the product sent is not covered by the warranty, then repairs can be carried out at the expense of the owner of the product (the final buyer). We reserve the right to require proof of purchase to resolve warranty claims. The warranty does not cover wear and tear, unauthorized modifications or modifications, misuse, improper care, accidents, or use other than for its intended purpose. La Sportiva accepts no liability for direct or indirect damages arising from the use of boots, including loss of boots, injury to third parties or other property damages.

Leather - chrome with increased moisture resistance, insulation - natural fur(sheepskin), reinforcing elements in the toe and heel parts, the optimal height of the boot ensures fixation of the ankle joint, creating stability when walking, preventing dislocations, a metal instep support (gel) to support the arch of the foot, a sole of increased wear resistance with high traction and anti-slip performance, during manufacture High-strength Guterman threads (Germany) are used. Shoe height: 16.5 cm.

Reinforcing elements in the toe and heel parts, optimal height, metal arch support (calendar) to support the arch of the foot, increased wear resistance sole with high traction rates, Cambrelle - a sweat-wicking material that can absorb three times more moisture than it weighs. It dries quickly and allows moisture to circulate; high-strength Guterman threads (Germany) are used in production. Shoe height: 16.5 cm.

An indispensable device made of frost-resistant rubber with metal spikes. Designed to prevent shoes from slipping while hiking on icy surfaces and dense snow, for winter sports. Easily and securely attached over any shoes from size 35 to 45. Season: winter Material: frost-resistant rubber, metal spikes

Lightweight universal mountain boots Article: 274 Sizes: 37-48 through 0.5 Pair weight: 1250 G Color: different Description Universal insulated boot for ice, mixed and rock routes. An excellent boot for technical mountaineering. The lightest model in its category. Water-repellent Cordura and FlexTec synthetic leather upper. The lacing system is similar to that used for climbing shoes. The HP3 midsole allows the use of crampons with step-in bindings. Upper: Cordura ® + Water-repellent Flex Tec leather Reinforcement: Water-repellent Lorica® Lining: Gore-Tex ®/Duratherm® Insole: Ibi-Thermo 9mm. Sole: Vibram ® with shock-absorbing insert Available in different colors and in Trango Evo GTX Woman art. 284 The excellent Trango S Evo GTX mountaineering boots are ideal for both icy climbs and rocky mountains. As the lightest boot in its category, the Trango S Evo is well insulated and offers excellent moisture protection thanks to Cordura and Flex Tec outer materials, as well as Lorica® reinforcements that are water-repellent. Innovative materials Gore-Tex® and Duratherm® provide good insulation, making this model possible to use in winter. The 3D Flex System ankle joints give your feet the mobility you need during heavy lifts. The highly abrasion-resistant Vibram ® outsole is equipped with a shock-absorbing insert that will soften the impact of landing on a hard surface, thereby providing greater comfort. For this model, crampons on soft and semi-rigid mounts will be relevant. Well, another pleasant advantage of the Trango S Evo GTX is the presence of a wide range of colors (which is very rare for this type of shoe), in which everyone can choose what they like best.

Lightweight mountain boot Upper Waterproof fabric+FlexTec2 Gore-Tex Perfomance Comfort lining Breathable Gore-Tex membrane lining Inner outsole PU under toe and heel. EVA insert. EVA insert in the center and under the heel for securing crampons. Vibram Cube outsole, IBS in the heel, climbing insert in the toe. The La Sportiva Cube's low-profile outsole is designed by Vibram. The outsole uses a special material to reduce the amount of rubber between the outsole and midsole. Accordingly, the weight of the boot is reduced. Welt for crampons The welt of the boot has a special shape of the heel and toe for attaching so-called “hard” crampons or only the heel for attaching semi-rigid crampons. With other boots, you can use soft crampons that do not require special attachment points. yes Area of ​​application Mountaineering Classic, technical mountaineering. Size 37-48 in 0.5 Pair weight 1130 g Colour: Yellow / Black Red / Yellow Description Lightweight mountain boots ideal for technical approaches and via ferrata routes. Distinctive features of this model: - new waterproof wear-resistant FlexTec2 boot upper - protective welt around the entire perimeter of the boot, which increases the wear resistance of the shoe - sewn-in tongue made of soft stretch fabric and providing the most comfortable fit on the foot - the unique La Sportiva “CUBE” Vibram sole has small volume, thanks to the use of special materials that reduce the overall weight of the boot. - special elastic gaiter - 3D-Flex system, which allows the boot to take an anatomical shape, while perfectly fixing the ankle - lacing from the very toe of the boot allows you to individually adjust the volume and fit to the leg Advantages and features allows the ankle to move freely, while providing sufficient fixation external fabric , which “breathes” and does not allow moisture to pass through the outside, a sole designed to reduce the impact load when walking and running, Vibram rubber Care instructions Clean the boots after each use. All external and internal hinges should be thoroughly cleaned and dried to reduce the risk of rust on metal products. Care for the leather outside and inside the shoe using special products. Leave the boots to dry outdoors, away from direct sunlight and away from heating devices. La Sportiva recommends choosing your boot size carefully: your foot should fit well in the last. By keeping your foot snug in the boot, you minimize the risk of tearing the Gore-Tex inner membrane. After each use, boots must be cleaned of dirt and dust by rinsing under a gentle stream of water. If necessary, the insole can be removed and the boots themselves can be placed in a cool, dry place for ventilation. It is best to remove the insole after each use and shake out any gravel that may have accidentally gotten inside the shoe and could damage the integrity of the Gore-Tex membrane. Do not place newspaper or other paper inside the boots as this may slow down the drying of the boots. Never dry your boots in the open sun or near heating devices. Never treat the upper materials with oil-containing products as this may adversely affect the waterproof performance and overall lifespan of the boot. We recommend Nikwax water-repellent products for the care of your shoes. These products are suitable for caring for models with a Gore-Tex membrane. Products must be applied to a damp surface to improve absorption into the boot fabric. The effect of this product lasts quite a long time, but not permanently. The product can be reapplied as needed or after each use in harsh conditions. GORE-TEX CARE We recommend using a water-based, wax-based product such as Nikwax for models with a Gore-Tex membrane to simultaneously protect leather and nylon from water. These products do not affect the technical characteristics and “breathing” properties of materials, including Gore-Tex, but create the necessary waterproof film on the boot.

Lightweight high-tech mountain boots with seamless Thermo Tech Injection construction Upper Wear-resistant material with Thermo Tech Injection coating Thermo Tech Injection is a method of “hot” application of a plastic coating that has high water-repellent properties. Gore-Tex Perfomance Comfort lining Breathable Gore-Tex membrane lining Insole Polyurethane under the toe and heel. EVA insert. EVA insert in the center and under the heel for securing crampons. Vibram Cube outsole, IBS in the heel, climbing insert in the toe. The La Sportiva Cube's low-profile outsole is designed by Vibram. The outsole uses a special material to reduce the amount of rubber between the outsole and midsole. Accordingly, the weight of the boot is reduced. Welt for crampons The welt of the boot has a special shape of the heel and toe for attaching so-called “hard” crampons or only the heel for attaching semi-rigid crampons. With other boots, you can use soft crampons that do not require special attachment points. yes Area of ​​application Mountaineering Classic, technical mountaineering. Size 37-48 in 0.5 Pair weight 1350 g Color: Blue / Red Yellow / Black Description Super light, highly technical mountaineering boots. Ideal for mixed routes, fast&light climbs and via ferrata routes. This model sets new standards in weight and comfort with its no-sew exterior and unique coating. This model received the prestigious Outdoor Industry Award, an annual prize given to the most innovative product in the outdoor sector. - New lacing system with clasps and thermoplastic coating reduces internal volume. - Super light and extremely comfortable thanks to the absence of external seams of the boot. The new construction method “Thermo Tech Injection” is used: a special thermoplastic coating, the most advanced water-repellent technology to date. - Maximum water-repellent protection - The La Sportiva “CUBE” sole, created by Vibram, uses a special material that reduces the amount of rubber and, as a result, the overall weight of the boot. -3D Flex System better supports and fixes the ankle joint on steep slopes, while allowing the boot to take an anatomical shape. - Durable polyurethane midsole in the toe and heel with a soft EVA insert in the center improves weight distribution and shock absorption. - Adjustable, removable EZ Flex tongue - have a back welt for crampons Upper: abrasion-resistant fabric + Thermo Tech Injection thermoplastic coating Lining: Gore-Tex Performance Comfort. Benefits and Features Allows the ankle to move freely while providing adequate support Removable tongue that attaches to the top of the boot Outer fabric that is breathable and waterproof Outsole designed to reduce the impact of walking and running Vibram rubber Awards Gold Medal Trango Cube GTX La Sportiva Trango Cube boots awarded a gold medal at Outdoor Friedrichshaffen. The expert commission awarded the highest award to the new innovative mountain boots of the Italian company Read more La Sportiva Trango Cube GTX among the best new products of 2013 according to the Gear Institute The Gear Institute's selection of the most innovative products that set new trends in the outdoor industry. There are several sports where the weight of the equipment has a great importance . Mountaineering certainly ranks first among them and the new La Sportiva Trango Cube GTX opens up new possibilities. They are much lighter than the popular Nepal Evo GTX and even lighter than La Sportiva's previous ultra-lightweight model, the Trango S Evo GTX. La Sportiva designers spent almost three years perfecting this model. The upper has a one-piece construction, the fastener system is attached without a single seam, and the new Vibram sole. Care instructions Clean your boots after each use. All external and internal hinges should be thoroughly cleaned and dried to reduce the risk of rust on metal products. Care for the leather outside and inside the shoe using special products. Leave the boots to dry outdoors, away from direct sunlight and away from heating devices. La Sportiva recommends choosing your boot size carefully: your foot should fit well in the last. By keeping your foot snug in the boot, you minimize the risk of tearing the Gore-Tex inner membrane. After each use, boots must be cleaned of dirt and dust by rinsing under a gentle stream of water. If necessary, the insole can be removed and the boots themselves can be placed in a cool, dry place for ventilation. It is best to remove the insole after each use and shake out any gravel that may have accidentally gotten inside the shoe and could damage the integrity of the Gore-Tex membrane. Do not place newspaper or other paper inside the boots as this may slow down the drying of the boots. Never dry your boots in the open sun or near heating devices. Never treat the upper materials with oil-containing products as this may adversely affect the waterproof performance and overall lifespan of the boot. We recommend Nikwax water-repellent products for the care of your shoes. These products are suitable for caring for models with a Gore-Tex membrane. Products must be applied to a damp surface to improve absorption into the boot fabric. The effect of this product lasts quite a long time, but not permanently. The product can be reapplied as needed or after each use in harsh conditions. GORE-TEX CARE We recommend using a water-based, wax-based product such as Nikwax for models with a Gore-Tex membrane to simultaneously protect leather and nylon from water. These products do not affect the technical characteristics and “breathing” properties of materials, including Gore-Tex, but create the necessary waterproof film on the boot.

Lightweight, high-tech mountain boots. Article: 11J Completeness: Medium Size: 32-48 in 0.5 Pair weight: 1350 G Colour: blue Description Super lightweight, highly technical climbing boots ideal for via ferrata routes. This model sets new standards in weight and comfort with its no-sew exterior and unique coating. This model received the prestigious Outdoor Industry Award, an annual prize given to the most innovative product in the outdoor sector. - New lacing system with clasps and thermoplastic coating reduces internal volume. - Super light and extremely comfortable thanks to the absence of external seams of the boot. The new construction method “Thermo Tech Injection” is used: a special thermoplastic coating, the most advanced water-repellent technology to date. - Maximum water-repellent protection - The La Sportiva “CUBE” sole, created by Vibram, uses a special material that reduces the amount of rubber and, as a result, the overall weight of the boot. -3D Flex System better supports and fixes the ankle joint on steep slopes, while allowing the boot to take an anatomical shape. - Durable polyurethane midsole in the toe and heel with a soft EVA insert in the center improves weight distribution and shock absorption. - Adjustable, removable EZ Flex tongue - have a back welt for crampons Upper: abrasion-resistant fabric + Thermo Tech Injection thermoplastic coating Lining: Gore-Tex Performance Comfort.

Universal anti-slip for cats. Made from rubber. Prevents snow from sticking to crampons. For all Salewa cat models (Dru, Alunal, Aguille and Titan).

Double boots for high altitude or winter climbing. Article: 835 Sizes: 37-48 through 0.5 Pair weight: 2400 g Color: silver Description Double boot for high-altitude or technical winter ascents. Outer boot: Thermal insulating polyurethane with waterproof microfiber inserts. Inner boot: Thermal insulating high-strength material. Sole: Vibram, replaceable. LA SPORTIVA BARUNTSE double climbing boots will be a good solution for all mountaineering enthusiasts who love to conquer great heights. Like all LA SPORTIVA brand boots, this model will provide you with maximum comfort even in the most extreme conditions. Thanks to the multilayer outer boot (it consists of five layers), your feet will be insulated from cold and wind. The inner boot is water-repellent thanks to microfiber inserts, so even if snow accidentally gets inside between the outer and inner boots, you can rest assured that your feet will remain dry. The high-quality Vibram sole is very strong and durable, so it will last a long time and will not let you down even on slippery surfaces, and if necessary, it can be removed and replaced. As a feature of LA SPORTIVA shoes, the lace system has already proven itself, which allows you to tie your laces even with one hand, without taking off your gloves. The weight of the boots is just under two and a half kilograms, for standard sizes 40-42. Which is a good indicator, given the high thermal insulation properties.

Double boots for high-altitude ascents up to GOST 7000-80 m Article: 296 Dimensions: 39-47 in 0.5 Weight of a pair: 2300 G Color: gray / yellow Description Double boots for high-altitude ascents up to GOST 7000-80 m. Ideal for climbing northern walls , for winter mountaineering and long stays at high altitude. Simple, comfortable and precise fit. A distinctive feature of this model is the original lacing system, both for the outer and inner boots, which allows you to lace the boot with one hand, in extreme conditions - with gloves. Very light, a pair of size 42 weighs only 2300 g. Can be used with any type of cat. Outer boot: PU-Tech synthetic fabric combined with a double layer of polyethylene with two densities. Inner: perforated thermoformed polyethylene Lining: Aluminum insulation combined with a protective wear-resistant perforated layer Inner sole: 5 mm thick. made of carbon fiber, with thermal structure, with a central polyester insert + aluminum thermal insulation Sole: Vibram ® + high protective rubber welt If you love mountaineering, then the La Sportiva Spantik double mountaineering boots will be an indispensable purchase for you. Thanks to the high-quality materials from which they are made, your feet will be warm even at an altitude of 7000-80 meters according to GOST. Aluminum thermal insulation over the entire area of ​​the boot in combination with high-quality polyester and polyethylene will not allow wind, moisture or frost to pass through. The Vibram outsole is also resistant to harsh outdoor conditions and will provide good traction on icy surfaces. For climbers, the ability to lace with one hand will be a definite plus, for example, if you are hanging at a height and need to adjust your boot. Plus, you can attach absolutely all types of climbing crampons to the sole: both rigid and semi-rigid - fortunately, this model supports this possibility (on most models it is possible to attach only a certain type of crampons). A good fit of the boots, as well as a light weight of just over two kilograms, will not cause any discomfort when moving. The range includes boots for all sizes.

CHIRUCA Nepal Pro mountain boots are the most powerful and durable from the model range of the Spanish shoe manufacturer. The Gore-Tex membrane provides excellent protection against water and has high performance in removing excess moisture from the surface of the skin (sweat). CHIRUCA Nepal Pro mountain boots are the standard of durability in footwear for tourism, hunting and mountaineering. Thick genuine leather in several layers with reinforcements on the heel protects against punctures and cuts even on sharp rocks. A special series of Vibram soles with increased wear resistance and an original tread for moving on unpaved surfaces with rocky rocks, and there are also special slots for installing spikes and crampons. Inside, the insole consists of two layers that soften shock loads on the foot when moving and remove moisture into the bottom porous layer of the insole, and antibacterial impregnation prevents unpleasant odor . The boot's cut with reinforcement at the heel increases durability and provides additional stability (protection against ankle injuries). Waterproof boots CHIRUCA NEPAL PRO with a Gore-Tex membrane are made of high quality genuine leather. The Gore-Tex membrane makes the boots absolutely waterproof, but at the same time allows your feet to “breathe”, thanks to the porous structure of the material. The Vibram Hunting outsole is made of natural rubber. "Vibram Hunting" is an excellent grip on all types of soil and rocky surfaces, as well as a guarantee of shoe durability. The sole of the NEPAL PRO boots is rigid and almost unbending, and has special grooves for attaching climbing crampons. All seams in the boot are made with overlap using Goodyear technology, which makes them completely waterproof. The two-layer insole will provide additional moisture removal. Hooks H.R.T. made of stainless steel and laces made of water-repellent polyester securely fix your foot in the boot. Waterproof leather boots with a Gore-Tex membrane. The Gore-Tex membrane provides excellent protection against water and has high vapor removal properties. Genuine leather impregnated with "Scotchgard" does not cause allergies and has good vapor removal due to the preservation of the pore structure. The "Vibram" outsole with increased wear resistance is made from natural rubber, which provides high grip and excellent stability on rough terrain, and most importantly, perfectly protects against heat loss. The shock-absorbing properties of the sole protect your joints from stress as much as possible. The insole consists of two layers of different densities. This combination provides additional convenience. Moisture is diverted into the lower porous layer of the insole, and antibacterial impregnation prevents the appearance of unpleasant odors. The boot's cut with reinforcement at the heel increases durability and provides additional stability (protection against ankle injuries). It is advisable to change shoes throughout the day so that different muscle groups work and your legs do not get tired, this is especially necessary for those who wear high heels. All seams are made using Goodyear technology - absolutely waterproof. Making overlapping seams will allow you to avoid tears, but many manufacturers have begun to practice butt seams on braid, which last no more than one season and flow like rivers inside the boot (whoever wants to buy cheap will always buy a pig in a poke). Few people think about it, but a heel is required for boots for active use (hunting, fishing (hiking). It allows you to increase the permeability and relieve the muscles of the foot (protection against flat feet). The most striking example of this is the instruction of Alexander the Great to use sandals with small heels for soldiers on long campaigns (the commander noticed that soldiers “in heels” walk much longer distances). Mountain boots CHIRUCA Nepal Pro - characteristics: pair weight -1.9 kg. (size 44); sole width 8-11 cm (size 44); outside instep coverage -47 cm (size 44); boot height -18 cm (size 44).

Combining the innovations of the STRATOS series, SYBORG is the ideal daily training boot for advanced skiers.

Women's ski boots combining high level comfort, wide fit of the boot and excellent performance characteristics for skiing on a variety of slopes. Sensor technology combines a 104mm last that still provides precise coverage, enhanced support in the heel and anatomically shaped foam in the toe. Women SPORT THERMO FIT PLUS technology is aimed at minimizing the impact on problem areas of the feet - it has improved coverage of the foot in the instep zone, a more clearly shaped ankle zone for exceptional comfort, free circulation and warmth retention. These are ski boots for multi-purpose universal skiing of a wide range of advanced skiers. Color: dark purple Brand ROSSIGNOL Gender Female Age Adult Model year 2015-16

Women's ski boots that combine a high level of comfort, a wide fit on the boot and excellent performance characteristics for skiing on a variety of slopes. Sensor technology combines a 104mm last that still provides precise coverage, enhanced support in the heel and anatomically shaped foam in the toe. WOMEN COMFORT FIT technology is aimed at minimizing the impact on problem areas of the feet - has improved coverage of the foot in the instep zone, a more defined ankle zone for exceptional comfort, free circulation and warmth retention. These are ski boots for multi-purpose universal skiing for a wide range of beginner level skiers. Brand ROSSIGNOL Gender Female Age Adult Model year 2015-16

Women's ski boots that combine a high level of comfort, a wide fit on the boot and excellent performance characteristics for skiing on a variety of slopes. Sensor technology combines a 104mm last that still provides precise coverage, enhanced support in the heel and anatomically shaped foam in the toe. Sensor Fit technology is designed to minimize impact on problem areas of the feet - with improved coverage at the instep and a more contoured ankle area for exceptional comfort, circulation and warmth. These are ski boots for multi-purpose universal skiing for a wide range of beginner level skiers. Hardness level: 50 Brand ROSSIGNOL Gender Female Age Adult Model year 2015-16

Comfortable, easy to use boot for children. Sensor Fit technology for greater comfort, performance and warmth. 4 adjustable cuff clips provide improved leg support and ease of use. Designed to help children learn to ski and have fun on the slopes. Brand ROSSIGNOL Gender Unisex Age Children Model year 2015-16

Comfortable and easy to use boot for children. Sensor Fit technology for greater comfort, performance and warmth. 3 clips with adjustable cuff provide improved leg support and ease of use. Designed to help children learn to ski and have fun on the slopes. Brand ROSSIGNOL Gender Unisex Age Children Model year 2015-16

Comfortable, easy to use boot for children. Sensor Fit technology for greater comfort, performance and warmth. 4 adjustable cuff clips provide improved leg support and ease of use. Designed to help children learn to ski and have fun on the slopes. Hardness: 50 Pad width: Jr Technology: Sensor Inside. Clips: 4 with macro adjustment - polycarbonate, diagonal. Combs: three-position Brand ROSSIGNOL Gender Unisex Age Children Model year 2014-15

Comfortable and easy to use boot for children. Sensor Fit technology for greater comfort, performance and warmth. 3 clips with adjustable cuff provide improved leg support and ease of use. Designed to help children learn to ski and have fun on the slopes. Technology: Sensor Inside. Outer boot: polyolefin, double injection. Inner boot: COMFORT FIT. Clips: 3 with macro adjustment - polycarbonate, diagonal. Combs: three-position Brand ROSSIGNOL Gender Unisex Age Children Model year 2014-15

Ski boots combining a high level of comfort, high rigidity, a wide last and excellent performance characteristics for skiing on a variety of slopes. The Alias ​​Sensor 100 is an all-around ski boot for a wide range of skiers from intermediate to expert skiers. Technology: Sensor. Outer boot: polyester. Inner: SPORT THERMO FIT PLUS, HEATING SOLE PRESET. Tongue: solid. 4 diagonal clips with micro adjustment (aluminum). Combs: 4th - QUICKSET 3-position, 3rd - three-position. Canting. Belt: 35 mm. Age Adult Gender Unisex Manufacturer ROSSIGNOL Model year 2014-15

The Elan Ezyy is a flexible children's boot with superior performance thanks to Elan's U-Flex technology for fast, effortless progress. Technical features: - The new Elan boots with U-Flex technology are endowed with flexibility that naturally follows the movements of the legs and takes the shape of the skis in an arc due to the movable forefoot. - Exceptional flexibility and increased mobility in the toe box combined with high-quality liner materials guarantee warmth and comfort. - Thanks to the Volume control spacer, one boot fits three sizes. The boots come with a special spacer that changes their internal volume depending on which side up or down it is installed in the boots.

The Elan Ezyy is a flexible children's boot with superior performance thanks to Elan's U-Flex technology for fast, effortless progress. Technical features: - The new Elan boots with U-Flex technology are endowed with flexibility that naturally follows the movements of the legs and takes the shape of the skis in an arc due to the movable forefoot. - Exceptional flexibility and increased mobility in the toe box combined with high-quality liner materials guarantee warmth and comfort. - Thanks to the Volume control spacer, one boot fits three sizes. The boots come with a special spacer that changes their internal volume depending on which side up or down it is installed in the boots.

The Elan Ezyy is a flexible children's boot with superior performance thanks to Elan's U-Flex technology for fast, effortless progress. Technical features: - The new Elan boots with U-Flex technology are endowed with flexibility that naturally follows the movements of the legs and takes the shape of the skis in an arc due to the movable forefoot. - Exceptional flexibility and increased mobility in the toe box combined with high-quality liner materials guarantee warmth and comfort. - Thanks to the Volume control spacer, one boot fits three sizes. The boots come with a special spacer that changes their internal volume depending on which side up or down it is installed in the boots.

Model DELIGHT 85 with built-in heating, which will provide warmth and comfort throughout the day. Features: Technologies: InTemp heating system, Power Link, volume control system and plate (VCR, VCP), Soft Step, power belt Stiffness index: 85 Outer boot: Polypropylene, Thin Shell construction Inner boot: 4DRY with built-in heating system Clips: 4 high pressure nylon clips

The Elan Bloom is a flexible children's boot with superior performance thanks to Elan's U-Flex technology for fast, effortless progress. Technical features: - The new Elan boots with U-Flex technology are endowed with flexibility that naturally follows the movements of the legs and takes the shape of the skis in an arc due to the movable forefoot. - Exceptional flexibility and increased mobility in the toe box combined with high-quality liner materials guarantee warmth and comfort. - Thanks to the Volume control spacer, one boot fits three sizes. - Included with the boots is a special spacer that changes their internal volume depending on which side up or down it is installed in the boots.

The Elan Bloom is a flexible children's boot with superior performance thanks to Elan's U-Flex technology for fast, effortless progress. Technical features: - The new Elan boots with U-Flex technology are endowed with flexibility that naturally follows the movements of the legs and takes the shape of the skis in an arc due to the movable forefoot. - Exceptional flexibility and increased mobility in the toe box combined with high-quality liner materials guarantee warmth and comfort. - Thanks to the Volume control spacer, one boot fits three sizes. - Included with the boots is a special spacer that changes their internal volume depending on which side up or down it is installed in the boots.

The Elan Bloom is a flexible children's boot with superior performance thanks to Elan's U-Flex technology for fast, effortless progress. Technical features: - The new Elan boots with U-Flex technology are endowed with flexibility that naturally follows the movements of the legs and takes the shape of the skis in an arc due to the movable forefoot. - Exceptional flexibility and increased mobility in the toe box combined with high-quality liner materials guarantee warmth and comfort. - Thanks to the Volume control spacer, one boot fits three sizes. - Included with the boots is a special spacer that changes their internal volume depending on which side up or down it is installed in the boots.

The Elan Bloom is a flexible children's boot with superior performance thanks to Elan's U-Flex technology for fast, effortless progress. Technical features: - The new Elan boots with U-Flex technology are endowed with flexibility that naturally follows the movements of the legs and takes the shape of the skis in an arc due to the movable forefoot. - Exceptional flexibility and increased mobility in the toe box combined with high-quality liner materials guarantee warmth and comfort. - Thanks to the Volume control spacer, one boot fits three sizes. - Included with the boots is a special spacer that changes their internal volume depending on which side up or down it is installed in the boots.

Elan U-Flex technology allows ski boots to bend, helping the natural movements of the child's legs. And, of course, it does not interfere with the natural deflection of the ski with U-Flex technology. The ability to bend the boot and move the toes inside it, combined with the high quality of the materials used for the liner, allows you to keep children's feet really warm and comfortable. A special insole-inlay that controls the internal volume of the boot allows you to use 3 sizes in one boot, depending on its position. Adjusting the size is effortless and takes just seconds. Simply insert the insole on the desired side or turn it over. Brand Elan Gender Unisex Age Children Model year 2016-17

DELIGHT 75 is ideal for advanced skiers who value comfort. These boots are tailored to the shape and volume female legs, they are lightweight, and what is important - with a height-adjustable spoiler in the calf area, which allows you to adjust the volume in this often problematic area. Technologies: Volume Change System and Plate (VCR) Stiffness index: 75 Outer boot: Polypropylene, Thin Shell construction Inner boot: 4DRY with built-in heating system Clips: 3 aluminum clips Brand Elan Gender Female Age Adult Model year 2016-17

Elan U-Flex technology allows ski boots to bend, helping the natural movements of the child's legs. And, of course, it does not interfere with the natural deflection of the ski with U-Flex technology. The ability to bend the boot and move the toes inside it, combined with the high quality of the materials used for the liner, allows you to keep children's feet really warm and comfortable. A special insole-inlay that controls the internal volume of the boot allows you to use 3 sizes in one boot, depending on its position. Adjusting the size is effortless and takes just seconds. Simply insert the insole on the desired side or turn it over. Brand Elan Gender Female Age Children Model year 2016-17

The world's only children's ski boots with U-Flex technology that makes learning fun. Elastomeric inserts allow the boot to bend in three dimensions, following the natural movements of a child's foot, maintaining its mobility, and therefore warmth, and without interfering with the ski bending in the longitudinal direction. A special rotating insole system allows you to include 3 sizes in one shoe! Depending on the size, one or two clips are used. Technologies: U-Flex, VCP, Warm feet, 2 clips, PP Dimensions (cm): (20,20.5,21), (21.5,22,22.5) Age Child Gender Unisex Manufacturer Elan Model year 2015-16

Elan U-Flex technology allows ski boots to bend, helping the natural movements of the child's legs. And, of course, it does not interfere with the natural deflection of the ski with U-Flex technology. The ability to bend the boot and move the toes inside it, combined with the high quality of the materials used for the liner, allows you to keep children's feet really warm and comfortable. A special insole-inlay that controls the internal volume of the boot allows you to use 3 sizes in one boot, depending on its position. Adjusting the size is effortless and takes just seconds. Simply insert the insole on the desired side or turn it over. Construction: Cabrio construction Upper material: Polypropylene Lining: Thermo Insulation 1 buckle Age Children's Gender Unisex Manufacturer Elan Model year 2015-16

The world's only children's ski boots with U-Flex technology that makes learning fun. Elastomeric inserts allow the boot to bend in three dimensions, following the natural movements of a child's foot, maintaining its mobility, and therefore warmth, and without interfering with the ski bending in the longitudinal direction. A special rotating insole system allows you to include 3 sizes in one shoe! Depending on the size, one or two clips are used. U-Flex, VCP, Warm feet, 2 clips, PP Sizes (cm): (20,20.5,21), (21.5,22,22.5) Age Child Gender Unisex Manufacturer Elan Model year 2015-16

The world's only children's ski boots with U-Flex technology that makes learning fun. Elastomeric inserts allow the boot to bend in three dimensions, following the natural movements of a child's foot, maintaining its mobility, and therefore warmth, and without interfering with the ski bending in the longitudinal direction. A special rotating insole system allows you to include 3 sizes in one shoe! Depending on the size, one or two clips are used. Technologies: U-Flex, VCP, Warm feet, 1 clip, PP Sizes (cm): (16.5,17,17.5), (17,17.5,18) or (18.5,19,19.5) Age Children's Gender Unisex Manufacturer Elan Model year 2015-16

The world's only children's ski boots with U-Flex technology that makes learning fun. Elastomeric inserts allow the boot to bend in three dimensions, following the natural movements of a child's foot, maintaining its mobility, and therefore warmth, and without interfering with the ski bending in the longitudinal direction. A special rotating insole system allows you to include 3 sizes in one shoe! U-Flex, VCP, Warm feet, 2 clips, PP Sizes (cm): (20,20.5,21), (21.5,22,22.5) Age Child Gender Unisex Manufacturer Elan Model year 2015-16

The world's only children's ski boots with U-Flex technology that makes learning fun. Elastomeric inserts allow the boot to bend in three dimensions, following the natural movements of a child's foot, maintaining its mobility, and therefore warmth, and without interfering with the ski bending in the longitudinal direction. A special rotating insole system allows you to include 3 sizes in one shoe! U-Flex, VCP, Warm feet, 1 clip, PP Sizes (cm): (16.5,17,17.5), (17,17.5,18) or (18.5,19,19.5) Age Child Gender Unisex Manufacturer Elan Model year 2015 -16

The Delight 65 ski boots are especially good when paired with skis from W Studio. Features: -adapted to the shape and volume of the female leg -lightweight, with a height-adjustable spoiler in the calf area, which allows you to adjust the volume in this often problematic area Technologies: -InTemp heating system The main heating zone is located in the toes - exactly where it is most often required. The electronic control system provides two heating levels and is equipped with an energy saving function. Once the boots are fully warmed up, this system automatically switches to a low-power mode, increasing the duration of operation -Power Link, volume control system and plate (VCR, VCP), Soft Step, power belt - Stiffness index: 65 - Last width : 102 mm -Outer boot: Polypropylene, Thin Shell construction -Inner boot: 4DRY with built-in heating system -Sizes: 220, 225, 230, 235, 240, 245, 250, 255, 260, 265, 270, 275 -Clips: 3 high-pressure nylon clips (all three with micro-adjustment) Batteries are not included! Brand Elan Gender Female Age Adult Model year 2015-16

For the 2015/16 season, Elan released Delight ski boots, which are especially good when paired with skis from W Studio. These boots are adapted to the shape and volume of the female leg, they are lightweight, and what is important - with a height-adjustable spoiler in the calf area, which allows you to adjust the volume in this often problematic area. The stiffness index is typical for mid-level women's boots -65 units, and they are surprisingly comfortable. A distinctive feature is that inside these boots there is an electric heater. The batteries are built into the inner boot at the back of the boot - they will provide the skier with warmth for a period of five to six hours. The main heating zone is located in the finger area - exactly where it is needed most often. The electronic control system provides two heating levels and is equipped with an energy saving function. Once the boots are fully warmed up, this system automatically switches to a low-power mode, extending the running time. Features of Delight boots Technologies: InTemp heating system, Power Link, volume change system and plate (VCR, VCP), Soft Step, power belt Stiffness index: 65 Last width: 102 mm Outer boot: Polypropylene, Thin Shell construction Inner boot: 4DRY with built-in heating system Sizes: 220, 225, 230, 235, 240, 245, 250, 255, 260, 265, 270, 275 Clips: 3 high-pressure nylon clips (all three with micro-adjustment) Brand Elan Gender Female Age Adult Model year 2015-16

Women's ski boots, designed for skiing on prepared slopes, are light and comfortable, the interior is lined with artificial fur that is soft and pleasant to the touch. Designed for maximum comfort all day long and in all weather conditions. Specifications: - Boot stiffness: 60 - polyolefine outer boot - anatomical insoles - VCR - level adjustment

Lightweight, warm, breathable, comfortable boots for hiking, traveling and the winter city Shoe SoftShell with water-repellent impregnation and elements made of heat-resistant polyurethane Three-component sole: Bottom layer: EVA (EVA) Middle layer : PU insert with plastic stiffeners in the heel area Outer layer: Oil and petrol resistant rubber Lining: Fleece + Textile material with Hydroguard® membrane Recommended temperature range - up to -15C Sizes: 36-46 In the very name of the boots there are echoes of mountain landslides, carpets from edelweiss, alluring snowy peaks. However, the boots are not intended for mountaineering and high-altitude expeditions - rather for foothills, low altitudes, and cross-country hiking in winter and in the cold off-season. The boots securely fix the foot and ankle joint, protect the feet from stones and impacts, do not get wet and remove excess moisture from the inside, and protect from the cold. The top of the boots is made of shoe SoftShell, which combines the functions of moisture protection, wind protection and an insulating layer. The necessary rigidity of the upper is provided by elements made of heat-resistant polyurethane. The lining of the boots is a textile material with a “Hydroguard”® membrane, which breathes, does not get wet, removes excess moisture well, maintaining a comfortable temperature inside, and soft, cozy fleece protects the feet from moisture and from hypothermia. Reliable grip on the ground, stability on any terrain, the necessary rigidity and elasticity of the boot are ensured by a three-composition sole (oil- and petrol-resistant rubber + polyurethane insert with plastic stiffeners + EVA). Three-composition soles improve shock absorption and reduce the weight of the shoes. EVA (ethylene vinyl acetate) is a lightweight and elastic material, similar to foam rubber, with excellent shock-absorbing properties. It springs well, quickly restores its shape after deformation, remains flexible at low temperatures and has a low degree of heat transfer. Polyurethane is a polymer-based product. The special structure makes it viscous under the influence of external force. At the same time it provides thermal insulation and shock absorption. Additional rigidity under the heel is provided by plastic reinforcements in the heel area. The outsole is made of oil- and petrol-resistant rubber with a deep tread that provides reliable traction on various types of soil in any weather. A special molded anatomical insole, highly resistant to wear and antibacterial properties, maintains the correct position of the foot and provides ventilation. The heel gently and reliably holds the ankle, and the rubber pad in the toe of the boot protects the toes from impact and increases the grip area on rocky terrain. A sewn-in tongue with soft filling reduces the likelihood of getting wet and snow, water and forest debris getting into the boot. Durable lacing secures the foot tightly, is easy to tighten and quickly release. To make it easier for you to “feel” the shoes, our stores have “slides” - simulators of complex terrain.

Boots for mountaineering. The Mountain Trainer Mid GTX features a 1.6mm thick suede upper, complemented by thick nylon for the tongue and throat, updated 3F System support, and a protective TPU welt - Suede upper - Overlap tongue construction for a better fit - lining - GORE-TEX ® - full water and wind protection - Vibram ® WTC outsole - -3F nylon sockliner - rigid heel and ankle support - FLEX cuff increases range and provides comfort during descents - weight 550 g

Boots for technical high-altitude ascents. Article: 11I Upper: suede Lining: Dentex Midsole: LaSpoFlex 0.8 mm (front section only) Outsole: Vibram ® XS Grip2 3.5 mm Sizes: 35-48 in 0.5 Pair weight: 1780 G Color: yellow / black Description High-tech lightweight boots from Nepal series. Designed for difficult technical ascents at height and for climbing with crampons on mixed terrain. Made from full-cut 3 mm genuine leather with water-repellent impregnation. The GORE-Tex membrane reliably protects your feet from getting wet and wicks moisture out, so your feet always remain dry. The 3D Flex system provides ankle support and, together with the adjustable, removable EZ Out tongue, ensures a precise fit. A rubber welt around the perimeter protects the skin from abrasion during fast descents on scree. Vibram IBS outsole with easy replacement.

Boots for technical ascents and mixed routes Upper 3 mm water-repellent Idro-Perwanger leather 3 mm reverse Idro-Perwanger leather with water-repellent impregnation Gore-Tex Insulated Comfort lining Breathable Gore-Tex membrane lining Inner sole 2 mm polyurethane of variable thickness. Special shape for fastening cats. Vibram IBS outsole with easy replacement Vibram, Impact Brake System. Possibility of easy replacement of the sole. Can be used with any types of cats, including "step-in" ones. Welt for crampons The welt of the boot has a special shape of the heel and toe for attaching so-called “hard” crampons or only the heel for attaching semi-rigid crampons. With other boots, you can use soft crampons that do not require special attachment points. yes Area of ​​application Mountaineering Classic, technical mountaineering. Size 36-48 in 0.5 Pair weight 1780 g Color: Yellow Description High-tech lightweight boots from the Nepal series. Designed for difficult technical ascents at height and for climbing with crampons on mixed terrain. Made from full-cut 3 mm genuine leather with water-repellent impregnation. The GORE-Tex membrane reliably protects your feet from getting wet and wicks moisture out, so your feet always remain dry. The 3D Flex system provides ankle support and, together with the adjustable, removable EZ Out tongue, ensures a precise fit. A rubber welt around the perimeter protects the skin from abrasion during fast descents on scree. Benefits and Features Allows the ankle to move freely while providing adequate support Removable tongue that attaches to the top of the boot Nylon loop for quick release of the lacing system Outer fabric that is breathable and moisture resistant Outsole designed to reduce impact when walking and running Vibram rubber model made of genuine leather Care instructions Clean the shoes after each use. All external and internal hinges should be thoroughly cleaned and dried to reduce the risk of rust on metal products. Care for the leather outside and inside the shoe using special products. Leave the boots to dry outdoors, away from direct sunlight and away from heating devices. La Sportiva recommends choosing your boot size carefully: your foot should fit well in the last. By keeping your foot snug in the boot, you minimize the risk of tearing the Gore-Tex inner membrane. Although La Sportiva boots are made from waterproof, specially treated leather that is resistant to dirt, improper use can cause the leather to dry out and become damaged. After each use, boots must be cleaned of dirt and dust by rinsing under a gentle stream of water. If necessary, the insole can be removed and the boots themselves can be placed in a cool, dry place for ventilation. It is best to remove the insole after each use and shake out any gravel that may have accidentally gotten inside the shoe and could damage the integrity of the Gore-Tex membrane. Do not place newspaper or other paper inside the boots as this may slow down the drying of the boots. Never dry your boots in the open sun or near heating devices. LEATHER CARE: Never treat these leathers with oil-containing products as this may adversely affect the waterproof performance and overall life of the boot. We recommend Nikwax water-repellent products for the care of your shoes. These products are suitable for caring for models with a Gore-Tex membrane. Products must be applied to damp skin to improve absorption into the boot fabric. The effect of this product lasts quite a long time, but not permanently. The product can be reapplied as needed or after each use in harsh conditions. Please be careful as these products darken the boot leather. CARE OF GORE-TEX We recommend using water and wax-based products, such as Nikwax, for leather models with a Gore-Tex membrane to simultaneously protect leather and nylon from water. These products do not affect the technical characteristics and “breathing” properties of materials, including Gore-Tex, but create the necessary waterproof film on the boot.

Boots for technical climbing Article: 280 Sizes: 37-48 in 0.5 Pair weight: 2050 G Color: yellow/black Description One of the best boots for technical mountaineering. Can be used at altitudes up to 5000 m. This model embodies all the main technological achievements of La Sportiva over the years: Ibi-Thermo inner sole; high quality leather upper; Vibram IBS outsole and insulated Gore-Tex/Duratherm lining; modern EZ Roller lacing system; a removable EZ Flex tongue allows you to individually adjust the boot to your foot and a special EZ Out loop makes it easier to unlace the boot. Equipped with a Comfort Footbed insole. Can be used with any type of cat. Upper: 3+ mm Idro-Perw reverse leather. with water-repellent impregnation Lining: Gore-Tex ®/Duratherm® Inner sole: thermal insulating Ibi-Thermo 9 mm. Sole: Vibram ® IBS The Nepal Evo GTX mountaineering boots are by far one of the best boots for climbers who prefer both technical and high-altitude climbs up to 5000 meters. Very high-quality lining from modern materials Gore-Tex® and Duratherm® makes this model waterproof and breathable, and the Comfort Footbed insole well insulates the cold from the bottom. The exclusive Ibi-Thermo inner sole in combination with the outer layer of Vibram ® IBS (Impact Brake System) also insulates well against frost and is a good shock absorber on hard surfaces. The Nepal Evo GTX can be equipped with any type of crampon, depending on the type of difficulty and conditions of your climb. The removable EZ Flex tongue allows you to customize the shoe perfectly to your foot, while still ventilating the interior thanks to its special material. The patented EZ OUT quick unlace system will reduce this process to a minimum of time. A standard pair of boots weighs only two kilograms, which is very good compared to similar shoes from other manufacturers.

Boots for rock and mixed routes Article: 336 Sizes: 37-48 through 0.5 Pair weight: 1600 g Color: gray Description Universal insulated boot for ice, mixed and rock routes. An excellent boot for technical mountaineering. The lightest model in its category. Water-repellent Cordura and FlexTec synthetic leather upper. The lacing system is similar to that used for climbing shoes. The HP3 midsole allows the use of crampons with step-in bindings. Upper: Cordura ® + Water-repellent Flex Tec leather Reinforcement: Water-repellent Lorica® Lining: Gore-Tex ®/Duratherm® Insole: Ibi-Thermo 9mm. Sole: Vibram ® with shock-absorbing insert Another mountaineering and climbing boot from the Trango family. This model of boots is ideal for all lovers of mixed routes who are going to conquer both ice walls and sheer rocks at the same time. Well insulated, the Trango Extreme Evo Light GTX can withstand heavy loads thanks to the modern Vibram ® outsole, which is equipped with a shock-absorbing insert, so it will soften your jumps on hard surfaces. The additional Ibi-Thermo 9mm inner sole will also provide a more comfortable walking experience. These boots can be used perfectly with step-in crampons, which is achieved by the presence of an HP3 midsole. The upper material of the boot is Cordura ® combined with artificial leather Flex Tec, equipped with water-repellent impregnation. Gore-Tex® and Duratherm® linings also keep moisture out while still allowing your feet to breathe while allowing good air circulation inside. The lacing system is similar to the lacing system for rock shoes. Well, an indisputable advantage, of course, is the minimal weight of the boots.

Ice climbing boots Upper 3 mm water-repellent Idro-Perwanger leather 3 mm water-repellent Idro-Perwanger leather Thermal Synergy lining Insole 9 mm insulating lbi-Thermo insulating inner sole 9 mm Ibi-Thermo Vibram IBS outsole with easy replacement Vibram, Impact Brake System. Possibility of easy replacement of the sole. Can be used with any types of cats, including "step-in" ones. Welt for crampons The welt of the boot has a special shape of the heel and toe for attaching so-called “hard” crampons or only the heel for attaching semi-rigid crampons. With other boots, you can use soft crampons that do not require special attachment points. yes Area of ​​application Mountaineering Classic, technical mountaineering. Size 37-48 in 0.5 Pair weight 2250 g Color: Yellow Description Recommended for use in high mountains and on icy surfaces. Thermal insulating version of the Nepal Top boots. Ideal for technical use on all types of mountain surfaces at high altitudes, they use an innovative triple-laminated lining. The insulating Ibi-Thermo insole reliably protects against the cold. It is possible to use cats. The new removable EZ FLEX tongue allows you to individually adjust the boot to your foot. The EZ OUT pull ring helps you unfasten the clasp that secures the lacing. The new HP3 midsole eliminates toe wear by using only the latest high-tech materials. There is a removable heat-insulating insole. Upper: 3mm water-repellent Idro-Perwanger ® leather Lining: Thermal Synergy Insole: 9mm insulating Ibi-Thermo Sole: Vibram ® with emergency braking system. Compatible with cats. Sizes: 37-48, every 0.5. 49 and 50 (on request). Weight: 2250 g / pair Benefits and features removable tongue attached to the top of the boot Nylon loop that allows you to quickly remove the lock from the lacing system outsole designed to reduce the impact of walking and running Vibram rubber model made of genuine leather Care instructions Clean the boots after every use. All external and internal hinges should be thoroughly cleaned and dried to reduce the risk of rust on metal products. Care for the leather outside and inside the shoe using special products. Leave the boots to dry outdoors, away from direct sunlight and away from heating devices. La Sportiva recommends choosing your boot size carefully: your foot should fit well in the last. By keeping your foot snug in the boot, you minimize the risk of tearing the Gore-Tex inner membrane. Although La Sportiva boots are made from waterproof, specially treated leather that is resistant to dirt, improper use can cause the leather to dry out and become damaged. After each use, boots must be cleaned of dirt and dust by rinsing under a gentle stream of water. If necessary, the insole can be removed and the boots themselves can be placed in a cool, dry place for ventilation. It is best to remove the insole after each use and shake out any gravel that may have accidentally gotten inside the shoe and could damage the integrity of the Gore-Tex membrane. Do not place newspaper or other paper inside the boots as this may slow down the drying of the boots. Never dry your boots in the open sun or near heating devices. LEATHER CARE: Never treat these leathers with oil-containing products as this may adversely affect the waterproof performance and overall life of the boot. We recommend Nikwax water-repellent products for the care of your shoes. These products are suitable for caring for models with a Gore-Tex membrane. Products must be applied to damp skin to improve absorption into the boot fabric. The effect of this product lasts quite a long time, but not permanently. The product can be reapplied as needed or after each use in harsh conditions. Please be careful as these products darken the boot leather. CARE OF GORE-TEX We recommend using water and wax-based products, such as Nikwax, for leather models with a Gore-Tex membrane to simultaneously protect leather and nylon from water. These products do not affect the technical characteristics and “breathing” properties of materials, including Gore-Tex, but create the necessary waterproof film on the boot.

Boots for classic mountaineering and mountain tourism Upper 2.8 mm Idro-Perwanger leather+high cut fubric cuff 2.8 mm reverse leather. high cuff Gore-Tex Perfomance Comfort lining Breathable Gore-Tex membrane lining Inner sole 8 mm high density nylon. anti-torsion plate 8 mm high-strength nylon. insert to prevent sole from twisting Vibram outsole IBS Vibram, Impact Brake System. Welt for crampons The welt of the boot has a special shape of the heel and toe for attaching so-called “hard” crampons or only the heel for attaching semi-rigid crampons. With other boots, you can use soft crampons that do not require special attachment points. yes Area of ​​application Mountaineering Classic, technical mountaineering. Size 38-48 in 0.5 Pair weight 1750 g Color: Dark Green / Natural Anthracite / Red Description Karakorum Evo GTX are durable boots for classic mountaineering and mountain tourism. Each boot is made from a single piece of leather 2.8 millimeters thick with a special water-repellent treatment. Thus, a minimum number of seams is obtained, due to which the boot acquires additional strength. The boots have a Gore-Tex membrane, which does not allow moisture to pass inside, but at the same time has good breathability and wicks moisture away from the inside. This model is equipped with two welts for attaching hard crampons, but can also be used with semi-rigid or soft crampons. The boots have a wear-resistant Vibram sole, the quality of which has been tested by time. A rubber welt around the perimeter of the boot protects the leather from wear and tear during high-speed descents on scree. Thanks to Impact Brake System technology, which is a special tread pattern on the sole, better shock absorption is achieved, which reduces impact loads on joints and traction with terrain. The use of 3D Flex technology allows you to combine reliable ankle support with the flexibility of the boot needed for ease of movement. This is achieved through the use of thinner, more flexible leather in a specific area, so that the boot flexes forward as you step, but has flexural rigidity in the perpendicular plane, which will prevent ankle injury from awkward movement if you lace the boots tightly. Using special lace clips, you can independently adjust the tension in the foot and ankle areas. Benefits and Features Allows the ankle to move freely, while providing sufficient support Outer fabric that "breathes" and does not allow moisture to pass through Outsole designed to reduce the impact of walking and running Vibram rubber Model made of genuine leather Awards Aplin magazine has tested a number of mountaineering boots , awarded the "Alpin Berg" award to the La Sportiva Karakorum Evo GTX The German magazine Aplin tested a number of mountaineering boots and, based on the test results, awarded the "Alpin Berg" award to the La Sportiva Karakorum Evo GTX. Waterproof and highly breathable, reinforced tread on the sole, which really reduces the stress on the joints. High ankle, independent lacing adjustment - all this makes Karakorum Evo GTX boots irreplaceable. Care instructions Clean your boots after each use. All external and internal hinges should be thoroughly cleaned and dried to reduce the risk of rust on metal products. Care for the leather outside and inside the shoe using special products. Leave the boots to dry outdoors, away from direct sunlight and away from heating devices. La Sportiva recommends choosing your boot size carefully: your foot should fit well in the last. By keeping your foot snug in the boot, you minimize the risk of tearing the Gore-Tex inner membrane. Although La Sportiva boots are made from waterproof, specially treated leather that is resistant to dirt, improper use can cause the leather to dry out and become damaged. After each use, boots must be cleaned of dirt and dust by rinsing under a gentle stream of water. If necessary, the insole can be removed and the boots themselves can be placed in a cool, dry place for ventilation. It is best to remove the insole after each use and shake out any gravel that may have accidentally gotten inside the shoe and could damage the integrity of the Gore-Tex membrane. Do not place newspaper or other paper inside the boots as this may slow down the drying of the boots. Never dry your boots in the open sun or near heating devices. LEATHER CARE: Never treat these leathers with oil-containing products as this may adversely affect the waterproof performance and overall life of the boot. We recommend Nikwax water-repellent products for the care of your shoes. These products are suitable for caring for models with a Gore-Tex membrane. Products must be applied to damp skin to improve absorption into the boot fabric. The effect of this product lasts quite a long time, but not permanently. The product can be reapplied as needed or after each use in harsh conditions. Please be careful as these products darken the boot leather. CARE OF GORE-TEX We recommend using water and wax-based products, such as Nikwax, for leather models with a Gore-Tex membrane to simultaneously protect leather and nylon from water. These products do not affect the technical characteristics and “breathing” properties of materials, including Gore-Tex, but create the necessary waterproof film on the boot.

The La Sportiva Baruntse double climbing boots will be a good solution for all mountaineering enthusiasts who love to conquer great heights. Like all La Sportiva boots, this model will provide you with maximum comfort even in the most extreme conditions. Thanks to the multilayer outer boot (it consists of five layers), your feet will be insulated from cold and wind. The inner boot is water-repellent thanks to microfiber inserts, so even if snow accidentally gets inside between the outer and inner boots, you can rest assured that your feet will remain dry. Boots for high-altitude and winter ascents with removable liner Upper 3 mm water-repellent Idro-Perwanger leather 3 mm insulating Idro-Perwanger leather with water-repellent treatment Gore-Tex Insulated Comfort lining Breathable Gore-Tex membrane lining Insole 9 mm insulating lbi-Thermo thermal insulating inner sole 9 mm Ibi-Thermo Vibram IBS outsole with easy replacement Vibram, Impact Brake System. Possibility of easy replacement of the sole. Can be used with any types of cats, including "step-in" ones. Welt for crampons The welt of the boot has a special shape of the heel and toe for attaching so-called “hard” crampons or only the heel for attaching semi-rigid crampons. With other boots, you can use soft crampons that do not require special attachment points. yes Scope of application High-altitude mountaineering Climbing in the Himalayas, winter ascents, prolonged exposure to low temperatures. Size 37-48 in 0.5 Pair weight 2400 g Color: Silver Description Thermal insulating double boots with a removable inner boot are ideal for high-altitude and technical climbs. The outer boot with inserts made of synthetic insulation consists of five layers, providing reliable protection of the feet from the cold (see picture). The internal “breathable” boot with a quick lacing system consists of three layers: wear-resistant Cordura, a 7mm layer of EVA foam, and mesh material that guarantees maximum moisture removal. Vibram outsole, TPU midsole. Comfortable crampon welts, compatible with any model. Durable outer part, traditional lacing system. They have large sizes 49.50. Outer boot: high-tech polyurethane, synthetic thermal insulation material combined with a double layer of polyurethane. Water-repellent microfiber inserts. Lining: polyethylene and aluminum combined with a protective wear-resistant perforated layer Removable inner boot: molded thermal insulating material Sole: Vibram ® Sizes: 37-48 in 0.5. 49 and 50 (on request). Patent: Inner boot lacing system Weight: 2400g/pair Advantages and features Vibram rubber Care instructions Clean your boots after each use. · All external and internal hinges should be thoroughly cleaned and dried to reduce the risk of rust on metal products. · Leave the boots to dry outdoors, away from direct sunlight and away from heating devices. · La Sportiva recommends choosing your boot size carefully: your foot should fit well in the last. By keeping your foot snug in the boot, you minimize the risk of tearing the Gore-Tex ® inner membrane or Cambrelle ® material. After each use, boots must be cleaned of dirt and dust by rinsing under a gentle stream of water. If necessary, the insole can be removed and the boots themselves can be placed in a cool, dry place for ventilation. Never dry your boots in the open sun or near heating devices. Outer boot: high-tech polyurethane, synthetic thermal insulation material combined with a double layer of polyurethane. Water-repellent microfiber inserts. Lining: polyethylene and aluminum, combined with a protective wear-resistant perforated layer. The internal “breathable” boot with a quick lacing system consists of three layers: wear-resistant Cordura, a 7mm layer of EVA foam, mesh material that guarantees maximum moisture removal. Midsole: 6mm thick Ibi-Thermo + PE and aluminum insert. Outsole: Vibram ® Impact Brake System Suitable for all types of crampons. Gender: Male Presence of membrane: Without membrane Actual weight (kg): 1.2 Season: 17

Boots for high-altitude ascents in the Himalayas Article: 290 Sizes: 39-47 through 0.5 Weight of a pair: 2520 G Color: yellow/black Description Double boots for difficult high-altitude ascents in the Himalayas. Meet all modern requirements for high-altitude boots. This model is very compact and 15% lighter than similar models from other manufacturers. A special feature is the movable tongue, which ensures easy adjustment and a tight fit of the liner. New outsole with the highest thermal insulation properties and a front welt made of rubber with increased abrasion resistance. Can be used with any type of cat. Outer boot: upper - Cordura, inner part reinforced with Kevlar with polyurethane coating, with UV protection. Waterproof and UV-resistant Riri Storm zipper with placket. Inner: Highly durable nylon upper, dual-density polyethylene foam padding, thermally reflective aluminum lining. Inner sole: 5 mm thick carbon fiber with polyester insert, plus aluminum thermal insulation. Sole: special rubber with high heat-insulating properties. Double climbing boots La sportiva Olimpus Mons Evo are designed for difficult high-altitude climbs in the Himalayas, as well as in other equally high and snowy peaks. This model is distinguished by high gaiters, which protect against the ingress of snow and moisture, or, for example, stones. The interior of the outer boot is made of polyurethane-coated Kevlar, which, combined with the Cordura outer fabric and waterproof Riri Storm zipper (which, like the entire boot, is UV resistant) will keep you warm. The inner boot fits snugly to the foot, is completely sealed, and combines nylon, polyethylene foam and aluminum thermal insulation. The double sole of the boots also has excellent thermal insulation properties thanks to carbon fiber with polyester inserts and aluminum insulation, and does not slip even on ice, which is very important for mountaineering. In conclusion, it is worth noting that despite all the thermal insulation advantages, Olimpus Mons Evo boots are light in weight (only 2.5 kilograms!), when compared with similar models from other manufacturers.

3F EVO SYSTEM: A unique combination of flexibility, ankle support and a perfect fit, reinforced with steel wire for an extra snug heel fit. "Climbing" lacing from the toe of the boot. Cleansport NST internal odor treatment. Upper: All-round rubber welt, highly durable Cordura technical fabric, 1.6mm Nubuk leather. Lining: GORE-TEX® Performance Comfort. Insole: hard nylon + 27% fiberglass + possibility of individual adjustment to the foot. Sole: 3S Combi system - three-layer microporous rubber for greater rigidity, TPU insert on the heel for semi-automatic crampons + Vibram ® New Mulaz - with a deeper and clearer tread, high-strength, wear-resistant, “tenacious” on any terrain, with an asymmetrical profile. Weight 1/2: 625 g. Purpose: classic mountaineering Weight: Men's Size: 6-12, 13 UK Waterproofing: GORE-TEX ® Performance Comfort Brand Salewa Gender Male Age Adult Model Year 2015

3F system - combination of ankle flexibility + lateral support + perfect fit to the leg. "Climbing" lacing from the toe of the boot. Internal Cleansport NST anti-odor treatment. Upper: all-round rubber welt, 1.6 mm thick suede, high-strength Cordura technical fabric. Lining: breathable mesh fabric. Reinforced insole with the ability to adjust to the foot. Outsole: Vibram® Alpine Approach. Weight 1/2: 530 g. Purpose: Mountain trekking, hiking, Via Ferrata, Weight: Men's Size: 6-12, 13 UK Brand Salewa Gender Male Age Adult Model year 2015

3F system - combination of ankle flexibility + lateral support + perfect fit to the leg. "Climbing" lacing from the toe of the boot. Cleansport NST internal odor treatment. Upper: All-round rubber welt, high-strength Cordura technical fabric, 1.6mm suede. Lining: GORE-TEX® Extended Comfort. Reinforced insole with the ability to adjust to the foot. Outsole: Vibram® Alpine Approach. Weight 1/2: 630 g Purpose: Mountain trekking, hiking, Via Ferrata, Fullness: Men's Size: 6-12, 13 UK Water protection: GORE-TEX ® Extended Comfort Brand Salewa Gender Male Age Adult Model year 2015

3F system - combination of ankle flexibility + lateral support + perfect fit to the leg. "Climbing" lacing from the toe of the boot. Cleansport NST internal odor treatment. Upper: All-round rubber welt, highly durable Cordura technical fabric, 1.6mm Nubuk leather. Lining: full-grain leather. Reinforced insole with the ability to adjust to the foot. Outsole: Vibram® Alpine Approach. Weight 1/2: 530 g Purpose: Mountain trekking, hiking, Via Ferrata, Weight: Men's Size: 6-12, 13 UK Age Adult Gender Male Manufacturer Salewa Model year 2015

3F system - combination of ankle flexibility + lateral support + perfect fit to the leg. "Climbing" lacing from the toe of the boot. Internal Cleansport NST anti-odor treatment. Upper: all-round rubber welt, high-strength Cordura technical fabric, 1.6mm suede. Lining: GORE-TEX® Extended Comfort. Reinforced insole with the ability to adjust to the foot. Outsole: Vibram® Alpine Approach. Weight 1/2: 545 g Purpose: Mountain trekking, hiking, Via Ferrata, Fullness: Men's Size: 6-12, 13 UK Water protection: GORE-TEX ® Extended Comfort Brand Salewa Gender Male Age Adult Model year 2015

Climbing Boots - Upper - Suede - Overlap tongue construction for better fit - Lining - GORE-TEX ® - Full water and wind protection - Vibram ® WTC outsole - 3F - Rigid heel and ankle support - 3D lacing divides the lacing system into three individually adjustable ones sections (Feet, feet, cuffs). This allows you to fine-tune and customize the fit - FLEX cuff increases range and provides comfort during descents - weights 820g

Trekking boots for mountain hiking - Upper - suede - lining - GORE-TEX ® - complete water and wind protection - dual, ergonomic Vibram ® sole - Fit Footbed Plus allows you to adapt the shoe to the shape of your foot - 3F - rigid heel and ankle support - FLEX cuff increases range and provides comfort during descents - weight 670 g Brand Salewa Gender Male Age Adult Model year 2017

3F system - combination of ankle flexibility + lateral support + perfect fit to the leg. "Climbing" lacing from the toe of the boot. Internal Cleansport NST anti-odor treatment. Upper: all-round rubber welt, 1.6 mm suede. High-strength technical Cordura fabric. Lining: breathable mesh fabric. Reinforced insole with the ability to adjust to the foot. Outsole: Vibram® Alpine Approach. Weight 1/2: 455 g. Purpose: Mountain trekking, hiking, Via Ferrata, Weight: Women's Size: 3-9 UK Brand Salewa Gender Female Age Adult Model Year 2015

The Torq Lite Gtx is a mid-height boot with a Gore-Tex membrane and a thick rubber welt all around. Recommended use: #Via Ferrata# routes of varying difficulty, approaches to mountaineering routes and day walks in rocky terrain. Features: anatomical last structure system #DAS#2 a dense rubber welt around the entire circumference of the boot protects against abrasion on stones a lacing system from the toe to the top allows you to tightly and accurately fix the foot elastic material on the tongue for greater comfort membrane # GORE-TEX ® Extended Comfort # protects against getting wet and maintains good ventilation

Quality level according to the Dolomite Anatomic System - PERFORMANCE (DAS 3) - a complex system of an atomic close-fitting last + a special anatomical insole, inserts made of porous material, Vibram soles. Upper: rubber welt all around, treated with waterproof compound, breathable suede 1.6 to 1.8 mm thick + high-strength nylon fabric. Lining: GORE-TEX®. Insole: felt 2 mm thick. Sole: Vibram ®rubber bottom+ narrow part of the sole separating the so-called Climbing zone - honeycomb thermoplastic PU+ EVA layer throughout the sole. Weight 1/2: 470 g. Water protection: GORE-TEX ® Purpose: Long approaches, mountain trekking, via ferrata Size: 3-12.5 UK Fullness: universal Fit: Low Brand Dolomite Gender Male Age Adult Model year 2016- 17

Boots for sporty high mountain hiking - upper - suede / Schoeller®-Dynamic 1.6-1.8 - lining - Gore-Tex ® Sierra - waterproof and breathable, medium insulation - Ortholite ® 2D insole - easy to clean, wicks moisture - outsole Alp HC Vibram ® - high precision, dynamic, excellent grip - cuffs protect against snow, sand and stones - weight 640 g per boot

Boots for sporty high mountain hiking - upper - suede / Schoeller®-Dynamic 1.6-1.8 - lining - Gore-Tex ® Sierra - waterproof and breathable, medium insulation - Ortholite ® 2D insole - easy to clean, wicks moisture - outsole Alp HC Vibram ® - high precision, dynamic, excellent grip - cuffs protect against snow, sand and stones - weight 675 g per boot

Hiking boots - upper - suede / Mycrofiber 1.6-1.8 - lining - Performance Comfort - waterproof and breathable - felt insole - toe and heel protection - Vibram ® - high precision, balance, excellent grip - weight 521 g one boot

Quality level according to the Dolomite Anatomic System - HIGH PERFORMANCE (DAS4) - a complex system of anatomical tight-fitting last + special anatomical insole, rigid insert, anti-shock insert under the heel, Vibram sole. Upper: rubber welt all around, waterproof, breathable suede 1.6 to 1.8 mm thick + high-strength nylon fabric, stretch cuff at the top. Lacing in the lower part is in specially tailored loops and quick lacing in the upper part. Lining: GORE-TEX®. Insole: anatomical insole + double-density EVA insole with 3 mm fiberglass insert. Sole: Vibram ®rubber bottom+ PU-shock-absorbing inserts+ special insert in the heel area for semi-automatic crampons. Weight 1/2: 685 g Age Adult Gender Unisex Manufacturer Dolomite Model year 2015-16

Quality level according to the Dolomite Anatomic System - PERFORMANCE (DAS 3) - a complex system of an atomic close-fitting last + a special anatomical insole, inserts made of porous material, Vibram soles. Upper: rubber welt all around, treated with a waterproof compound, breathable suede with a thickness of 1.6 to 1.8 mm + high-strength stretch material, anatomical insulated cutout at the top, treated with stretch fabric + stretch gaiters + 2 sewn-in loops for easy pulling on the boot. Lining: GORE-TEX®. Insole: felt 2 mm thick. Sole: Vibram ®rubber bottom+ narrow part of the sole separating the so-called Climbing zone - honeycomb thermoplastic PU+ EVA layer throughout the sole. Weight 1/2: 590 g. Water protection: GORE-TEX ® Purpose: Long approaches, mountain trekking, via ferrata Size: 3-12.5 UK Fullness: universal Fit: High Brand Dolomite Gender Male Age Adult Model year 2017- 18

Boots for hiking and mountaineering - classic lacing system, one of the lightest boots - good grip on any surface - upper waterproof suede 1.6-1.8 mm + Soft Shell - lining GORE-TEX ® Extended Comfort Footwear Shoes made with featuring GORE-TEX® Extended Comfort technology, designed for both indoor and outdoor use in warm weather conditions and high temperatures. physical activity. Its long-lasting waterproof properties combined with breathability provide long-lasting protection from the elements. Water stays outside and does not penetrate inside, while sweat can easily come out. Thanks to the design without thermal insulation, this perfect choice for people who value a comfortable microclimate and heat dissipation. - anatomical Lite 4 insole - ASOFLEX Spiky midsole (effectively absorbs and distributes impact energy over a larger area) - Vibram 1229 Mulaz sole + double-density microporous insole + PU Anti-Shock insert - weight of one shoe -640 g Brand Asolo Gender Male Age Adult Model year 2017-18

ASOLO PIOLET GV MM is a model for classic mountaineering, but can also be used for mountain trekking. The model is distinguished by the manufacturer as durable, protected and waterproof boots for mountain hiking. The boots are built on a last model using a multi-component sole design. The boots use a combination of thick natural leather 2.4 mm thick with waterproof and vapor-permeable softshell material. The lower part of the model is protected by a dense layer of rubber. The lining of the boots is made of a two-component Gore-Tex membrane. - Outer layer: water-resistant suede 2.2-2.4 mm - Inner layer: Gore-Tex Performance Comfort - Anatomical insole: Lite 4 - Sole: Asolo/Vibram Ascent + microporosa a 2 densità + Dual Integrated - Weight: 860 g (half pair, size 8 UK) Materials and technologies: - Gore-Tex - a membrane that makes the shoes waterproof, breathable and comfortable - Vibram - high-tech sole, guaranteeing stability and strength. Brand Asolo Gender Female Age Adult Model Year 2016-17

A tough and technological boot for classic mountaineering in summer at altitudes up to 5000 m, or heavy, high-altitude trekking. Features a durable full-grain leather upper with excellent hold. Double tongue. Due to the fact that the boot is comfortable not only for climbing the summit, but also for simply walking along the trails, it is perfect for climbs with long approaches. The structure and tread pattern provide good grip both when climbing and when braking the foot. Thanks to the rigid sole and rear welt, it is compatible with semi-automatic and soft crampons. Technical characteristics: Upper: high-quality, full-cut leather from Perwanger (thickness 2.2-2.4 mm) with waterproof impregnation and soft shell from the Swiss company Schjeller make the boot durable and waterproof. The rubber lining around the entire perimeter increases wear resistance and strength, protects the toe from impacts and external influences. Membrane: GORE-TEX ® Performance Comfort Footwear - will prevent the boot from getting wet, allowing you to breathe and create the necessary climate inside in a different temperature range. Anatomical insole: Lite 4 Midsole: Nylon and Asoflex Spiky carbon fiber Outsole: Asolo/Vibram Ascent + dual-density microporous layer + Dual Integrated System will provide the necessary control, support and stability on difficult terrain, good traction and a high level of comfort. Compatible with semi-automatic cats. Weight: 860 gr. (1/2 pair for size 8 UK) Country of origin: Italy Gender: Men's Brand Asolo Gender Male Age Adult Model year 2017-18

ASOLO ELBRUS GV MM - trekking boots - the model is distinguished by the manufacturer as durable, protected and waterproof boots for mountain hiking. The boots are built on a last model using a multi-component sole. The Asolo Elbrus GV boots use a combination of thick natural leather with a thickness of 1.6 to 1.8 mm, with waterproof and vapor-permeable softshell material from Schoeller. The lower part of the model is protected by a dense layer of rubber. The boot lining is made of a two-component Gore-Tex membrane. Elbrus GV boots are built on the basis of the Vibram Ascent outsole, which is used in almost all the latest models of backpacking boots from this brand. The sole has a multi-component structure, consisting of a molded flexible fiberglass instep, an intermediate shock-absorbing layer of EVA foam and Asoflex polyurethane inserts, as well as a dense wear-resistant layer of thermopolyurethane outsole. - Outer layer: moisture-resistant suede 1.6-1.8 mm - Inner layer: Gore-Tex ® - Anatomical insole: Vario Asolflex - Last: MM (men's) - Sole: Asolo / Vibram - Weight: 800 g (half pair, size 8 UK) Materials and technologies: - Gore-Tex - membrane that makes the shoes waterproof, breathable and comfortable. - Vibram - a high-tech sole that guarantees stability and durability. Brand Asolo Gender Male Age Adult Model Year 2016-17

The top of the boot is waterproof Pervanger leather with a thickness of 2.2-2.4 mm. The lining is Gore-Tex insulated. Reinforced bottom of the boot - double Asoflex reinforced with nylon and fiberglass + EVA coating. Anatomical Lite3 insole. Purpose: Classic mountaineering, winter climbing Sole: Vibram Vertical/ Asolo+ frame made of Pebax+PU shock absorber Water protection: Gore-Tex insulated Weight: 980 g (one shoe size 8 UK) Water protection: Gore-Tex insulated Purpose of shoes: Classic mountaineering, winter climbing Age Adult Gender Male Manufacturer Asolo Model year 2014

The upper of the boot is waterproof Pervanger leather with a thickness of 2.2-2.4 mm. Lining - Gore-Tex insulated. Reinforced bottom of the boot - double Asoflex reinforced with nylon and fiberglass + EVA coating. Anatomical Lite3 insole. Purpose: Classic mountaineering, winter climbing Sole: Vibram Vertical/ Asolo+ frame made of Pebax+PU shock absorber Water protection: Gore-Tex insulated Weight: 980 g (one boot size 8 UK)

The upper is waterproof Pervanger leather with a thickness of 2.2-2.4 mm. Lining - Gore-Tex Performance. Reinforced bottom of the boot - Asoflex Ascent system. Anatomical Lite3 insole. Purpose: Classic mountaineering. Work in mountainous areas. Sole: Vibram Vertige for crampons "Step - in" Water protection: Gore-Tex Performance Weight: 990 g (one shoe size 8 UK) Water protection: Gore-Tex Performance Shoe purpose: classic mountaineering Brand Asolo Gender Unisex Age Adult Model year 2016-17

The upper of the boot is waterproof material Schoeller K-Tech Microtech+ microfiber. Lining - Gore-Tex insulated. The reinforced bottom of the boot is double Asoflex material made of nylon with fiberglass + EVA coating integrated into it. Anatomical Lite3 insole. Purpose: Technical mountaineering, combined routes. Outsole: Vibram Vertical/ Asolo+ Pebax frame+PU shock absorber Waterproofing: Gore-Tex insulated Weight: 910g (one size 8 UK boot)

The upper boot is Pebax plastic, the inner boot is corduroy + sinsulate insulation. Asoframe system - from Pebax. Anatomical AFS insole. Purpose: Technical and high-altitude mountaineering, ice climbing Sole: Two-color Vibram nilgiri Water protection: no Weight: 1200 g (one boot size 8 UK) Purpose of footwear: Technical and high-altitude mountaineering, ice climbing

Boots for hiking and mountaineering - classic lacing system, one of the lightest boots - good grip on any surface - upper waterproof suede 1.6-1.8 mm + Soft Shell - lining GORE-TEX ® Extended Comfort Footwear Shoes made with using GORE-TEX ® Extended Comfort technology, designed for use both indoors and outdoors in warm weather conditions and with high physical activity. Its long-lasting waterproof properties combined with breathability provide long-lasting protection from the elements. Water stays outside and does not penetrate inside, while sweat can easily come out. Thanks to the design without thermal insulation, it is an ideal choice for people who value a comfortable microclimate and heat dissipation. - anatomical Lite 4 insole - ASOFLEX Spiky midsole (effectively absorbs and distributes impact energy over a larger area) - Vibram 1229 Mulaz sole + double-density microporous insole + PU Anti-Shock insert - weight of one shoe -640 g

Double high-altitude climbing boots. Designed for high-altitude ascents, polar expeditions, and designed for very cold weather. They consist of an outer boot equipped with the Boreal Dry Line system and an inner boot insulated with Thinsulate. One-piece upper: Yes Upper material: Split Leather 2.8 mm, Cordura, Neopren, Abrasion-resistant Cordura with Sympatex ® membrane, 6mm EVA for shock absorption, breathable neoprene insole, heel lock for the correct position of the inner boot Insulation: Thinsulate Membrane: Sympatex Sole: Boreal Mount FDS-3 Vibration damping system: Yes Midsole: Boreal PBG-680 Operating mode: Designed for high-altitude ascents, polar expeditions, designed for very cold weather. Welt for fastening crampons: Yes Insole ventilation: Yes Moisture removal system: Boreal Dry Line Weight of a pair of size 41 rus, g: 2615 The outer boot is a one-piece upper made of high-quality Dynatec material with Lorica, carbon glass and neoprene. Wear-resistant Cordura with Sympatex ® membrane, 6mm EVA layer for maximum thermal insulation and vibration damping, the outsole allows you to attach crampons of any design, front and rear welt for crampons, special tread pattern, four-layer midsole, inner sole with a layer of neoprene 1.4 mm thick, quick lacing system built-in mini-gaiter Inner boot: made of durable fabric with an applied Sympatex membrane insulated with Thinsulate comfortable system of elastic Velcro fasteners for a tight anatomical fit outer layer of the outer sole made of neoprene anatomical tongue with a layer of neoprene (3 mm) and EVA (10 mm) for better thermal insulation lateral surfaces, tongue and heel of the boot are made of soft genuine leather, a two-layer insole with antibacterial impregnation and instep support

The outer part of the boots is made of one-piece leather, 2.8 mm thick. Bi-Flex system for maximum driving comfort. Three-piece adjustable tongue. Neoprene cuff reduces heat loss. Heel locking system for a perfect fit. Rubber welt to protect the boot and foot from stones. Boreal Dry-Line lining and three layers of Thinsulate are waterproof, breathable and cold-resistant. Vibram Teton sole with vibration-damping EVA layers of different densities, with crampon welts. Features: neoprene cuff to reduce heat loss Bi-Flex - movable cuff provides maximum comfort when moving HFS - reliable heel fixation Boreal Dry-Line - system of membrane and special moisture-wicking fibers. Unsurpassed moisture management and waterproofing Thinsulate insulation Vibram Teton sole with two crampon welts.

Designed for moving along glaciers and snow couloirs, passing classic mountaineering routes. one-piece leather upper without seams external water-repellent impregnation high ankle sole allows you to fasten crampons of any design double-sided welt for crampons deep tread pattern four-layer EVA-Pro midsole two-layer ventilated insole with antibacterial impregnation and arch support moisture-wicking surface of the insole does not cause allergies the upper edge of the boot the inside is treated with very soft leather, quick lacing system, special water-repellent laces, the kit includes a can of moisture-wicking impregnation and a Boreal mini-catalog Technical details: Upper material: Split Leather 2.6 mm Membrane: Sympatex Sole: Boreal Mount FDS-3 Vibration damping system Midsole: triple Operating mode: intended for use in heavy snow conditions and mountaineering routes Welt for attaching crampons Insole ventilation Moisture removal system: Boreal Dry Line Weight of a pair of size 7 UK, g: 1800

Boots for mixed and ice climbing Upper Wear-resistant material with Thermo Tech Injection coating Gore-Tex Insulated Comfort lining Insulating 3mm carbon Honeycomb Tech inner sole Vibram Cube outsole, IBS in the heel, climbing insert in the toe. Welt for crampons yes Area of ​​application Mountaineering Size 36-48 through 0.5 Weight of a pair 1380 g Boots with sewn-in gaiters are an ideal choice for mixed and ice ascents. Extremely light and comfortable boots thanks to the seamless Thermo Tech Injection upper technology. + thanks to the thermoplastic upper, the boots have reduced weight and bulk + Gore-Tex Insulated Comfort lining guarantees warmth, moisture protection and breathability + two welts for crampons + exclusive La Sportiva Cube Vibram outsole + built-in snow gaiters with waterproof zipper + lightweight Firm and anti-deformation HoneyComb Tech carbon fiber footbed + 3D Flex system for greater freedom of movement and precision on steep slopes

Mountaineering boots. They are insulated with Thinsulate, which allows them to be used in harsh climatic conditions. The Boreal Mount FDS-3 sole is made from a single piece of triple-density rubber and is designed to accommodate crampons of any design. The Shock absorption system softens shock loads when walking.

Technical, lightweight, waterproof climbing boots with Boa system. Technical, waterproof climbing boots with Boa system. The gaiter of the boots is made of elastic waterproof Cordura and Waterproof SM membrane. The external zipper with Velcro closure is waterproof and provides additional protection against moisture. The inner boot consists of 4 layers: the outer layer is waterproof Cordura, then there is a layer of fleece, an additional insulating layer of polyethylene foam, and a breathable wear-resistant mesh. The Boa system allows you to adjust the tension of the boots at the bottom of the foot area, and the Velcro fastener at the top of the ankle. Thanks to the Flex Zone in the ankle area, the boots are quite flexible and do not restrict movement. There is a rubber welt along the entire perimeter of the boots, which additionally protects the boots from damage from small stones. Vibram Matterhorn outsole with aggressive tread and Impact Brake System, which further reduces impact on the knees and ankles. Upper waterproof elastic Cordura + Waterproof SM membrane + wear-resistant fabric Lining Wear-resistant breathable mesh Insole Carbon insulation, Honey-Comb Tech 3mm Outsole Vibram Matterhorn + IBS Welt for crampons yes Area of ​​application High-altitude mountaineering Size 37-48 through 0.5 Pair weight 1710 g

The lightweight double boot consists of an outer boot and a removable inner boot. Integrated gaiter: The lower part is abrasion-resistant outer material and a waterproof membrane, the upper part is a durable and breathable material with a Sympatex membrane. Inner boot: The outer layer is one-piece seamless Cordura with a Sympatex membrane and a layer of 6mm perforated foam. Boot liner: made from a lightweight and warm three-layer laminate. The outer synthetic durable layer is combined with a layer of heat-reflecting aluminum film and an insulating layer of EVA foam. Three-layer Thinsulate lining with breathable Dry-Line membrane. Midsole: Multi-layer three layers of Thinsulate, 2 layers of neoprene 2mm thick, vibration-damping layers of EVA and PU. The external welt is made of thermopolyurethane, allowing the use of double welt crampons. Outsole: Vibram Teton. Features: Removable liner, quick lacing with Velcro adjustment on liner and liner, sophisticated multi-layer construction for maximum insulation and waterproofing, outer bootie with built-in gaiter, outer and inner bootie with crampon welts, Sympatex and Dry-Line materials for superior breathability and waterproofing . Characteristics Upper material: wear-resistant synthetic material Insulation: Thinsulate Membrane: Sympatex Sole: Vibram Teton Vibration damping system Midsole: Boreal PBG-680 Operating mode: high-altitude mountaineering, extremely cold conditions Welt for attaching crampons Insole ventilation Moisture removal system: Boreal Dry Line Weight of pair size 7 UK, g: 2920