Summer is rapidly coming to an end, and with it school break. On September 1, boys and girls will sit down at their desks again, meet with their classmates and teachers. And in order for them to be comfortable at school, they need a comfortable school uniform. We have already published for a boy, and now, by your numerous requests, we offer a jacket pattern for a girl.

This is a jacket for girls with reliefs, pockets with rounded flaps and double-seam sleeves - real find for the first cool days of September! And with the help of our step by step instructions you can sew such a jacket yourself.

Taking measurements

Fig.1. Measurements for a girl

Height - 128 cm

------------- 1/2 volume

Bust - 64 cm 32 cm

Waist - 54 cm 27 cm

Hip circumference - 66 cm 33 cm

Neck girth - 28 cm 14 cm

Shoulder length - 10 cm

Arm length - 40 cm

Back length to waist (DTS) - 28 cm

Front length to waist (accident) - 30 cm

Back Width (WB)

Chest Width (WH)

The length of the jacket on the back is about 43 cm.

The increase in freedom of fitting to the half-girth of the chest is 3 cm. Distribute the increase as follows: to the back - 0.7 cm, to the armhole - 1 cm, to the front - 1.3 cm.

See fig. 1.

Construction of a jacket pattern

Fig.2. Building a jacket pattern for a girl

We start building a jacket pattern by building a grid. Mesh width AB = 35 cm (half circumference of the chest according to the measurements + 3 cm (increase in freedom of fitting for all sizes)). Mesh length AC = 43 cm - the length of the jacket to measure.

Armhole depth. AG \u003d (armhole depth by measure + 1 cm). Draw a horizontal line from point G to the right. Designate the point of intersection with the BC G1.

Waistline. AT \u003d Length of the back to the waist (DTS) + 0.5 cm (increase for the shoulders) - point T. Draw TT1 parallel to AB. From point A, set aside to the right 1/2 of the width of the back by measurement (SHS) + 0.7 cm - point P. From point B, set aside to the left 1/2 of the width of the chest by measurement (SHG) + 1.3 cm - point P1. From the obtained points, lower the perpendiculars to the GG1 line - points G2 and G3 are obtained.

Auxiliary points of the armhole back and front. Divide PG2 and P1G3 into 4 equal parts.

Building a back pattern

Back neckline. From point A, set aside 5.5 cm to the right (1/3 of the half-girth of the neck according to the measure + 0.5 cm: 14/3 + 0.5 \u003d 5.5 cm) and up 1.5 cm. Connect points A and 1.5 concave line.

Shoulder drop. from point P lay down 1.5 cm. Connect points 1.5 (neck) and 1.5 descent of the shoulder with a straight line, continue the line. Set aside 11 cm (shoulder length to measure + 1 cm for all sizes: 10 + 1 = 11 cm). The shoulder of the back of the jacket sits down when sewing.

Back armhole line. From the corner with the apex at point G2, draw a bisector 2 cm long. From point G2, set aside 2 cm to the right and 1 cm up. Draw the armhole line of the back from the extreme point of the shoulder, the middle point of the division of PG2, point 2 (angle bisector), to point 1.

Back line. From point 1 (lower point of the back armhole) draw a vertical line to the CD line, point T2 is obtained along the waist, the intersection with GG1 is point G4, the intersection with the DC line is point H.

Calculation of darts at the waist. The general solution of the darts at the waist: Half chest - Half waist = 32 cm - 27 cm = 5 cm. side tuck front. Connect points G4, 2 and H.

The center line of the back of the jacket. If necessary, you can fit the jacket along the line of the middle of the back. In this case, the tuck is built from the T point with a depth of about 1-1.5 cm and smoothly reduced to the G point. However, so that the jacket does not turn out to be narrow at the hips, the hips should be checked after the pattern is built.

Building a front pattern

Front neckline. From point B to the left, set aside 5.5 cm (1/3 of the half-girth of the neck by measurement + 0.5 cm: 14/3 + 0.5 = 5.5 cm) and down 6.5 cm (1/3 of the half-girth of the neck by measurement + 1.5 cm: 14/3+1.5=6.5 cm). Connect points 5.5 and 6.5 with a concave line.

Front shelf lift. Through point 5.5, draw a vertical dotted line up and down - to the waist line - point T3. From point T3 set aside up the length of the front to the waist according to the measure (accident) + 0.5 cm, point B1 is obtained.

Front shoulder descent. Set aside 2 cm from the point P1. Draw a segment V1P1 equal to the length of the shoulder according to the measurement.

Front armhole line. From the corner with the apex at point G3, draw a bisector 2 cm long. Draw an armhole line from the extreme point of the shoulder, the lower division point P1G3, point 2 (the bisector of the angle), to point 1, touching the segment G3G4.

Shelf relief line. From the midpoint of division P1G3, draw a smooth relief line to the DC line. Mark the point of intersection with the waistline as T4.

Waist darts in front. Set aside 1 cm from point T4 to the left and right, smoothly connect to the relief line. The top of the tuck is 5 cm below the armhole line.

Addition on board. From point C, set aside 3 cm to the right and 1.5 cm down, draw a vertical line of approach to the fastener. Draw a bead line as shown in the pattern drawing.

Pocket flap and pick. Mark the pocket entry point and pocket flap configuration as shown in the pattern drawing. Mark the line of the selection and reshoot the selection separately on tracing paper. The configuration of the flap of the pocket and the lapel of the jacket can be modified, depending on your preferences.

Fig.3. Construction of a collar and sleeve pattern for a jacket

A two-seam sleeve pattern and a collar pattern for a jacket are built in the same way as. One-piece collar stand with a detachable edge of the collar.

Details of the pattern - back, side, front, collar, collar and both parts of the sleeve are taken separately and cut out with seam allowances - 1.5 cm, allowances along the bottom of the jacket and sleeves - 3 cm. Front, side, sleeve allowances, collar, outer the details of the flaps of the pockets and both selections of the jacket are completely duplicated with thermal fabric.

Compilation simple models With simple patterns, which even beginners can handle. Without spending a lot of time in an hour and a half, a new new thing is ready!
Spectacular dress
A light dress pattern, which, if desired and with a wide belt, can unexpectedly turn out to be a tunic that is not a sin to wear with tight black trousers and high platform shoes. Believe, sew Short dress A beginner with no sewing skills is quite capable!
to photo hosting →
This pattern for a girl with a height of 164-170 cm and a size of 46,48,50 will require 100 cm of knitted fabric with a width of 150 cm. Although, if desired, you can always redo this pattern to any size. Skirt length 34 cm to the middle of the thigh, on original photo the length of the skirt is about 45-50 cm and a piece of fabric, so you need to take 15-20 cm longer.
to photo hosting →

Fold the fabric right side in, pin along the edge, fold and a few pins scattered throughout the fabric. Step back from the edge of the edge 1-2 cm, grind the line and cut the edge along this 1 line. Again, retreat 1.5-2 cm from the cut and draw a line, this is the middle of the back.
Depart from the upper cut 1.5 cm and draw a horizontal line, on this horizontal line from (.) A to the left, mark the points after 11 cm and after 34 cm (.) B.
From the point (.) A down the fold after 56 cm, mark (.) B, and from (.) B to the left horizontal, on it 24 cm (.) E and after 36 cm (.) D.
From (.) B down the vertical is 33 cm, and from (.) D to the left the vertical is 10 cm.
From (.) D vertical up to the intersection with the horizontal from (.) D. Make a conjugation.
From (.) G up, mark 2 cm and smoothly connect with (.) E.
It remains to build a neck-boat and the upper part of the shelf is ready. From (.) And set aside 4 cm down and smoothly connect with a point of 11 cm.
Now, before continuing further construction, you need to draw allowances for the seams. On knitwear, a 1 cm allowance is enough. Draw allowances along the shoulder seam, neckline, armhole, side seam and bottom.
Next, you need to build a skirt. Step down from (.) Г 2 cm and from this point draw a horizontal line equal to one quarter of the measurement of your hips minus 2-4 cm (this value depends on the extensibility of the knitwear, the more it stretches, the larger this number, but do not worry, since the fitting will decide everything.) From this point (.) down the vertical.
Further along the fold down the desired length of the skirt, I want 34 cm and from this point to the left the horizontal until it intersects with the vertical.
From the conditional (.) B (conditional because we retreated down 2 cm) to the left one quarter of your waist measurement minus 2-4 cm. I have it 19. I wanted to make the waist line 2 cm lower, respectively, the measurements have changed.
Connect point 19 with a smooth curved line to the side seam. On the fitting, the side seam is adjusted. Draw 1 cm seam allowances along the waist line and side seam, 3-4 cm seam allowance along the bottom.
Cut out the front and skirt. Attach a shelf to the opposite upper cut, chop, grind. Don't rush to cut. First you need to draw the neck of the back in accordance with the drawing. Put on the skirt, pin and cut out the details of the back and skirt.
Product assembly.
There is a seam on the back, and there you can leave a small incision and make an air loop. Stitch back seam. Process the neck of the back and shelves. Connect shoulder seams. The length of the seam to your taste is 5-7 cm or more from point 11. Connect side seams, the bottom of the sleeve from (.) B by 4-5 cm. Process the bottom and cut of the sleeves. Connect the side seams of the skirt. Stitch the middle seam of the skirt and, if you wish, make a slit for comfortable walking. Make an assembly on the back and shelf of the bodice. Pair with a skirt. Process the bottom of the skirt. The dress is sewn with a knitting needle, a zigzag stitch or a special knitted stitch.